Description
General cell set selection class for models that apply to sub-sets
of the mesh.
Currently supports cell selection from a set of points, a specified cellSet
or cellZone or all of the cells. The selection method can either be
specified explicitly using the \c selectionMode entry or inferred from the
presence of either a \c cellSet, \c cellZone or \c points entry. The \c
selectionMode entry is required to select \c all cells.
Usage
Examples:
\verbatim
// Apply everywhere
selectionMode all;
// Apply within a given cellSet
selectionMode cellSet; // Optional
cellSet rotor;
// Apply within a given cellZone
selectionMode cellZone; // Optional
cellSet rotor;
// Apply in cells containing a list of points
selectionMode points; // Optional
points
(
(2.25 0.5 0)
(2.75 0.5 0)
);
\endverbatim
All tutorials updated and simplified.
in which different solver modules can be selected in each region to for complex
conjugate heat-transfer and other combined physics problems such as FSI
(fluid-structure interaction).
For single-region simulations the solver module is selected, instantiated and
executed in the PIMPLE loop in the new foamRun application.
For multi-region simulations the set of solver modules, one for each region, are
selected, instantiated and executed in the multi-region PIMPLE loop of new the
foamMultiRun application.
This provides a very general, flexible and extensible framework for complex
coupled problems by creating more solver modules, either by converting existing
solver applications or creating new ones.
The current set of solver modules provided are:
isothermalFluid
Solver module for steady or transient turbulent flow of compressible
isothermal fluids with optional mesh motion and mesh topology changes.
Created from the rhoSimpleFoam, rhoPimpleFoam and buoyantFoam solvers but
without the energy equation, hence isothermal. The buoyant pressure
formulation corresponding to the buoyantFoam solver is selected
automatically by the presence of the p_rgh pressure field in the start-time
directory.
fluid
Solver module for steady or transient turbulent flow of compressible fluids
with heat-transfer for HVAC and similar applications, with optional
mesh motion and mesh topology changes.
Derived from the isothermalFluid solver module with the addition of the
energy equation from the rhoSimpleFoam, rhoPimpleFoam and buoyantFoam
solvers, thus providing the equivalent functionality of these three solvers.
multicomponentFluid
Solver module for steady or transient turbulent flow of compressible
reacting fluids with optional mesh motion and mesh topology changes.
Derived from the isothermalFluid solver module with the addition of
multicomponent thermophysical properties energy and specie mass-fraction
equations from the reactingFoam solver, thus providing the equivalent
functionality in reactingFoam and buoyantReactingFoam. Chemical reactions
and/or combustion modelling may be optionally selected to simulate reacting
systems including fires, explosions etc.
solid
Solver module for turbulent flow of compressible fluids for conjugate heat
transfer, HVAC and similar applications, with optional mesh motion and mesh
topology changes.
The solid solver module may be selected in solid regions of a CHT case, with
either the fluid or multicomponentFluid solver module in the fluid regions
and executed with foamMultiRun to provide functionality equivalent
chtMultiRegionFoam but in a flexible and extensible framework for future
extension to more complex coupled problems.
All the usual fvModels, fvConstraints, functionObjects etc. are available with
these solver modules to support simulations including body-forces, local sources,
Lagrangian clouds, liquid films etc. etc.
Converting compressibleInterFoam and multiphaseEulerFoam into solver modules
would provide a significant enhancement to the CHT capability and incompressible
solvers like pimpleFoam run in conjunction with solidDisplacementFoam in
foamMultiRun would be useful for a range of FSI problems. Many other
combinations of existing solvers converted into solver modules could prove
useful for a very wide range of complex combined physics simulations.
All tutorials from the rhoSimpleFoam, rhoPimpleFoam, buoyantFoam, reactingFoam,
buoyantReactingFoam and chtMultiRegionFoam solver applications replaced by
solver modules have been updated and moved into the tutorials/modules directory:
modules
├── CHT
│ ├── coolingCylinder2D
│ ├── coolingSphere
│ ├── heatedDuct
│ ├── heatExchanger
│ ├── reverseBurner
│ └── shellAndTubeHeatExchanger
├── fluid
│ ├── aerofoilNACA0012
│ ├── aerofoilNACA0012Steady
│ ├── angledDuct
│ ├── angledDuctExplicitFixedCoeff
│ ├── angledDuctLTS
│ ├── annularThermalMixer
│ ├── BernardCells
│ ├── blockedChannel
│ ├── buoyantCavity
│ ├── cavity
│ ├── circuitBoardCooling
│ ├── decompressionTank
│ ├── externalCoupledCavity
│ ├── forwardStep
│ ├── helmholtzResonance
│ ├── hotRadiationRoom
│ ├── hotRadiationRoomFvDOM
│ ├── hotRoom
│ ├── hotRoomBoussinesq
│ ├── hotRoomBoussinesqSteady
│ ├── hotRoomComfort
│ ├── iglooWithFridges
│ ├── mixerVessel2DMRF
│ ├── nacaAirfoil
│ ├── pitzDaily
│ ├── prism
│ ├── shockTube
│ ├── squareBend
│ ├── squareBendLiq
│ └── squareBendLiqSteady
└── multicomponentFluid
├── aachenBomb
├── counterFlowFlame2D
├── counterFlowFlame2D_GRI
├── counterFlowFlame2D_GRI_TDAC
├── counterFlowFlame2DLTS
├── counterFlowFlame2DLTS_GRI_TDAC
├── cylinder
├── DLR_A_LTS
├── filter
├── hotBoxes
├── membrane
├── parcelInBox
├── rivuletPanel
├── SandiaD_LTS
├── simplifiedSiwek
├── smallPoolFire2D
├── smallPoolFire3D
├── splashPanel
├── verticalChannel
├── verticalChannelLTS
└── verticalChannelSteady
Also redirection scripts are provided for the replaced solvers which call
foamRun -solver <solver module name> or foamMultiRun in the case of
chtMultiRegionFoam for backward-compatibility.
Documentation for foamRun and foamMultiRun:
Application
foamRun
Description
Loads and executes an OpenFOAM solver module either specified by the
optional \c solver entry in the \c controlDict or as a command-line
argument.
Uses the flexible PIMPLE (PISO-SIMPLE) solution for time-resolved and
pseudo-transient and steady simulations.
Usage
\b foamRun [OPTION]
- \par -solver <name>
Solver name
- \par -libs '(\"lib1.so\" ... \"libN.so\")'
Specify the additional libraries loaded
Example usage:
- To run a \c rhoPimpleFoam case by specifying the solver on the
command line:
\verbatim
foamRun -solver fluid
\endverbatim
- To update and run a \c rhoPimpleFoam case add the following entries to
the controlDict:
\verbatim
application foamRun;
solver fluid;
\endverbatim
then execute \c foamRun
Application
foamMultiRun
Description
Loads and executes an OpenFOAM solver modules for each region of a
multiregion simulation e.g. for conjugate heat transfer.
The region solvers are specified in the \c regionSolvers dictionary entry in
\c controlDict, containing a list of pairs of region and solver names,
e.g. for a two region case with one fluid region named
liquid and one solid region named tubeWall:
\verbatim
regionSolvers
{
liquid fluid;
tubeWall solid;
}
\endverbatim
The \c regionSolvers entry is a dictionary to support name substitutions to
simplify the specification of a single solver type for a set of
regions, e.g.
\verbatim
fluidSolver fluid;
solidSolver solid;
regionSolvers
{
tube1 $fluidSolver;
tubeWall1 solid;
tube2 $fluidSolver;
tubeWall2 solid;
tube3 $fluidSolver;
tubeWall3 solid;
}
\endverbatim
Uses the flexible PIMPLE (PISO-SIMPLE) solution for time-resolved and
pseudo-transient and steady simulations.
Usage
\b foamMultiRun [OPTION]
- \par -libs '(\"lib1.so\" ... \"libN.so\")'
Specify the additional libraries loaded
Example usage:
- To update and run a \c chtMultiRegion case add the following entries to
the controlDict:
\verbatim
application foamMultiRun;
regionSolvers
{
fluid fluid;
solid solid;
}
\endverbatim
then execute \c foamMultiRun
This utility now always creates two patches, and only creates duplicate
faces when they connect to different cells and point in opposite
directions. Now that ACMI has been removed, there is no need to create
duplicate faces on the same cell and with similar orientations. This is
unituitive and is now considered an invalid mesh topology.
The preferred syntax for createBaffles is now as follows:
internalFacesOnly true;
baffles
{
cyclics
{
type faceZone;
zoneName cyclicFaces;
owner
{
name cyclicLeft;
type cyclic;
neighbourPatch cyclicRight;
}
neighbour
{
name cyclicRight;
type cyclic;
neighbourPatch cyclicLeft;
}
}
}
Note that the 'patches' sub-dictionary is not needed any more; the
'owner' and 'neighbour' sub-dictionaries can be in the same dictionary
as the parameters with which faces are selected. For backwards
compatibility, however, a 'patches' sub-dictionary is still permitted,
as are keywords 'master' and 'slave' (in place of 'owner' and
'neighbour', respectively).
The 'patchPairs' syntax has been removed. Whilst consise, this syntax
made a number of assumptions and decisions regarding naming conventions
that were not sufficiently intuitive for the user to understand without
extensive reference to the code. If identical boundaries are desired on
both sides of the patch, dictionary substitution provides a more
intuitive way of minimising the amount of specifiection required. For
example, to create two back-to-back walls, the following specification
could be used:
internalFacesOnly true;
fields true;
baffles
{
walls
{
type faceZone;
zoneName wallFaces;
owner
{
name baffleWallLeft;
type wall;
patchFields
{
p
{
type zeroGradient;
}
U
{
type noSlip;
}
}
}
neighbour
{
name baffleWallRight;
$owner; // <-- Use the same settings as for the owner
}
}
}
The following examples in the tutorials ($FOAM_TUTORIALS) directory have
been converted from using AMI to the new NCC system:
+ compressible/rhoPimpleFoam/RAS/annularThermalMixer
+ incompressible/pimpleFoam/RAS/propeller
+ lagrangian/particleFoam/mixerVessel2D (formerly mixerVesselAMI2D)
+ multiphase/interFoam/RAS/mixerVessel
+ multiphase/interFoam/RAS/propeller
+ multiphase/multiphaseEulerFoam/laminar/mixerVessel2D (formerly mixerVesselAMI2D)
The following tutorial has been converted from using ACMI:
+ incompressible/pimpleFoam/RAS/oscillatingInlet
The following tutorial has been converted from using Repeat AMI:
+ incompressible/pimpleFoam/RAS/impeller
The following tutorial has been added to demonstrate NCC's ability to
create a sufficiently conservative solution in a closed domain to
maintain phase fraction boundedness:
+ multiphase/interFoam/laminar/mixerVessel2D
The following tutorials have been added to demonstrate NCC's ability to
simulate partially overlapping couples on curved surfaces:
+ incompressible/pimpleFoam/RAS/ballValve
+ multiphase/compressibleInterFoam/RAS/ballValve
The following tutorial has been added to provide a simple comparison of
the conservation behaviour of AMI and NCC:
+ incompressible/pimpleFoam/laminar/nonConformalChannel
The following tutorial has been removed, as there were sufficiently many
examples involving this geometry:
+ incompressible/pimpleFoam/laminar/mixerVesselAMI2D
It is not clear for what cases the minVol control is useful or necessary and for
some cases it causes problems with snapping and layer addition if not set to a
sufficiently small value.
The defaultPatch type currently defaults to empty which is appropriate for 1D
and 2D cases but not when creating the initial blockMesh for snappyHexMesh as
the presence of empty patches triggers the inappropriate application of 2D point
constraint corrections following snapping and morphing. To avoid this hidden
problem a warning is now generated from blockMesh when the defaultPatch is not
explicitly set for cases which generate a default patch, i.e. for which the
boundary is not entirely defined. e.g.
.
.
.
Creating block mesh topology
--> FOAM FATAL IO ERROR:
The 'defaultPatch' type must be specified for the 'defaultFaces' patch, e.g. for snappyHexMesh
defaultPatch
{
name default; // optional
type patch;
}
or for 2D meshes
defaultPatch
{
name frontAndBack; // optional
type empty;
}
.
.
.
All the tutorials have been update to include the defaultPatch specification as
appropriate.
motionSmootherAlgoCheck::checkMesh is used by snappyHexMesh to check the mesh
after snapping and morphing. The minVol test which checks for collapsed cells
is now relative to the cube of the minimum bounding box length so that it is
less dependent on the size of the geometry and less likely to need changing for
very small geometries.
The default value is set in
etc/caseDicts/mesh/generation/meshQualityDict
etc/caseDicts/mesh/generation/meshQualityDict.cfg
//- Minimum cell pyramid volume relative to min bounding box length^3
// Set to a fraction of the smallest cell volume expected.
// Set to very negative number (e.g. -1e30) to disable.
minVol 1e-10;
The unused minArea and minTriangleTwist tests have been removed
The handling of the div(phid,p) term for transonic support in the pressure
equation is now consistent such that conservation is achieved at convergence of
the pressure system irrespective of the scheme chosen for div(phid,p) and the
relaxation of the pressure equation.
The rhoSimpleFoam tutorials have been updated and improved.
In rhoPimpleFoam, rhoSimpleFoam, buoyantPimpleFoam and buoyantSimpleFoam the
density prediction step at the start of pEqn.H is now consistent between these
solvers and the other compressible solvers. If the density is relaxed in the
corrector it is now also relaxed following the predictor which improves
consistency, stability and convergence.
The unreliable extrapolateProfile option has been replaced by the more flexible
and reliable profile option which allows the velocity profile to be specified as
a Function1 of the normalised distance to the wall. To simplify the
specification of the most common velocity profiles the new laminarBL (quadratic
profile) and turbulentBL (1/7th power law) Function1s are provided.
In addition to the new profile option the flow rate can now be specified as a
meanVelocity, volumetricFlowRate or massFlowRate, all of which are Function1s of
time.
The following tutorials have been updated to use the laminarBL profile:
multiphase/multiphaseEulerFoam/laminar/titaniaSynthesis
multiphase/multiphaseEulerFoam/laminar/titaniaSynthesisSurface
The following tutorials have been updated to use the turbulentBL profile:
combustion/reactingFoam/Lagrangian/verticalChannel
combustion/reactingFoam/Lagrangian/verticalChannelLTS
combustion/reactingFoam/Lagrangian/verticalChannelSteady
compressible/rhoPimpleFoam/RAS/angledDuct
compressible/rhoPimpleFoam/RAS/angledDuctLTS
compressible/rhoPimpleFoam/RAS/squareBendLiq
compressible/rhoPorousSimpleFoam/angledDuctImplicit
compressible/rhoSimpleFoam/angledDuctExplicitFixedCoeff
compressible/rhoSimpleFoam/squareBend
compressible/rhoSimpleFoam/squareBendLiq
heatTransfer/chtMultiRegionFoam/shellAndTubeHeatExchanger
heatTransfer/chtMultiRegionFoam/shellAndTubeHeatExchanger
incompressible/porousSimpleFoam/angledDuctImplicit
incompressible/porousSimpleFoam/straightDuctImplicit
multiphase/interFoam/RAS/angledDuct
Class
Foam::flowRateInletVelocityFvPatchVectorField
Description
Velocity inlet boundary condition creating a velocity field with
optionally specified profile normal to the patch adjusted to match the
specified mass flow rate, volumetric flow rate or mean velocity.
For a mass-based flux:
- the flow rate should be provided in kg/s
- if \c rho is "none" the flow rate is in m3/s
- otherwise \c rho should correspond to the name of the density field
- if the density field cannot be found in the database, the user must
specify the inlet density using the \c rhoInlet entry
For a volumetric-based flux:
- the flow rate is in m3/s
Usage
\table
Property | Description | Required | Default value
massFlowRate | Mass flow rate [kg/s] | no |
volumetricFlowRate | Volumetric flow rate [m^3/s]| no |
meanVelocity | Mean velocity [m/s]| no |
profile | Velocity profile | no |
rho | Density field name | no | rho
rhoInlet | Inlet density | no |
alpha | Volume fraction field name | no |
\endtable
Example of the boundary condition specification for a volumetric flow rate:
\verbatim
<patchName>
{
type flowRateInletVelocity;
volumetricFlowRate 0.2;
profile laminarBL;
}
\endverbatim
Example of the boundary condition specification for a mass flow rate:
\verbatim
<patchName>
{
type flowRateInletVelocity;
massFlowRate 0.2;
profile turbulentBL;
rho rho;
rhoInlet 1.0;
}
\endverbatim
Example of the boundary condition specification for a volumetric flow rate:
\verbatim
<patchName>
{
type flowRateInletVelocity;
meanVelocity 5;
profile turbulentBL;
}
\endverbatim
The \c volumetricFlowRate, \c massFlowRate or \c meanVelocity entries are
\c Function1 of time, see Foam::Function1s.
The \c profile entry is a \c Function1 of the normalised distance to the
wall. Any suitable Foam::Function1s can be used including
Foam::Function1s::codedFunction1 but Foam::Function1s::laminarBL and
Foam::Function1s::turbulentBL have been created specifically for this
purpose and are likely to be appropriate for most cases.
Note
- \c rhoInlet is required for the case of a mass flow rate, where the
density field is not available at start-up
- The value is positive into the domain (as an inlet)
- May not work correctly for transonic inlets
- Strange behaviour with potentialFoam since the U equation is not solved
See also
Foam::fixedValueFvPatchField
Foam::Function1s::laminarBL
Foam::Function1s::turbulentBL
Foam::Function1s
Foam::flowRateOutletVelocityFvPatchVectorField
Mesh motion and topology change are now combinable run-time selectable options
within fvMesh, replacing the restrictive dynamicFvMesh which supported only
motion OR topology change.
All solvers which instantiated a dynamicFvMesh now instantiate an fvMesh which
reads the optional constant/dynamicFvMeshDict to construct an fvMeshMover and/or
an fvMeshTopoChanger. These two are specified within the optional mover and
topoChanger sub-dictionaries of dynamicFvMeshDict.
When the fvMesh is updated the fvMeshTopoChanger is first executed which can
change the mesh topology in anyway, adding or removing points as required, for
example for automatic mesh refinement/unrefinement, and all registered fields
are mapped onto the updated mesh. The fvMeshMover is then executed which moved
the points only and calculates the cell volume change and corresponding
mesh-fluxes for conservative moving mesh transport. If multiple topological
changes or movements are required these would be combined into special
fvMeshMovers and fvMeshTopoChangers which handle the processing of a list of
changes, e.g. solidBodyMotionFunctions:multiMotion.
The tutorials/multiphase/interFoam/laminar/sloshingTank3D3DoF case has been
updated to demonstrate this new functionality by combining solid-body motion
with mesh refinement/unrefinement:
/*--------------------------------*- C++ -*----------------------------------*\
========= |
\\ / F ield | OpenFOAM: The Open Source CFD Toolbox
\\ / O peration | Website: https://openfoam.org
\\ / A nd | Version: dev
\\/ M anipulation |
\*---------------------------------------------------------------------------*/
FoamFile
{
format ascii;
class dictionary;
location "constant";
object dynamicMeshDict;
}
// * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * //
mover
{
type motionSolver;
libs ("libfvMeshMovers.so" "libfvMotionSolvers.so");
motionSolver solidBody;
solidBodyMotionFunction SDA;
CofG (0 0 0);
lamda 50;
rollAmax 0.2;
rollAmin 0.1;
heaveA 4;
swayA 2.4;
Q 2;
Tp 14;
Tpn 12;
dTi 0.06;
dTp -0.001;
}
topoChanger
{
type refiner;
libs ("libfvMeshTopoChangers.so");
// How often to refine
refineInterval 1;
// Field to be refinement on
field alpha.water;
// Refine field in between lower..upper
lowerRefineLevel 0.001;
upperRefineLevel 0.999;
// Have slower than 2:1 refinement
nBufferLayers 1;
// Refine cells only up to maxRefinement levels
maxRefinement 1;
// Stop refinement if maxCells reached
maxCells 200000;
// Flux field and corresponding velocity field. Fluxes on changed
// faces get recalculated by interpolating the velocity. Use 'none'
// on surfaceScalarFields that do not need to be reinterpolated.
correctFluxes
(
(phi none)
(nHatf none)
(rhoPhi none)
(alphaPhi.water none)
(meshPhi none)
(meshPhi_0 none)
(ghf none)
);
// Write the refinement level as a volScalarField
dumpLevel true;
}
// ************************************************************************* //
Note that currently this is the only working combination of mesh-motion with
topology change within the new framework and further development is required to
update the set of topology changers so that topology changes with mapping are
separated from the mesh-motion so that they can be combined with any of the
other movements or topology changes in any manner.
All of the solvers and tutorials have been updated to use the new form of
dynamicMeshDict but backward-compatibility was not practical due to the complete
reorganisation of the mesh change structure.
for consistency with the regionToCell topo set source and splitMeshRegions and
provides more logical extension to the multiple and outside point variants insidePoints,
outsidePoint and outsidePoints.
This required standardisation of the mapping between the class and selection
names of the solid transport models:
constIso -> constIsoSolid
exponential -> exponentialSolid
polynomial -> polynomialSolid
to provide a single consistent code and user interface to the specification of
physical properties in both single-phase and multi-phase solvers. This redesign
simplifies usage and reduces code duplication in run-time selectable solver
options such as 'functionObjects' and 'fvModels'.
* physicalProperties
Single abstract base-class for all fluid and solid physical property classes.
Physical properties for a single fluid or solid within a region are now read
from the 'constant/<region>/physicalProperties' dictionary.
Physical properties for a phase fluid or solid within a region are now read
from the 'constant/<region>/physicalProperties.<phase>' dictionary.
This replaces the previous inconsistent naming convention of
'transportProperties' for incompressible solvers and
'thermophysicalProperties' for compressible solvers.
Backward-compatibility is provided by the solvers reading
'thermophysicalProperties' or 'transportProperties' if the
'physicalProperties' dictionary does not exist.
* phaseProperties
All multi-phase solvers (VoF and Euler-Euler) now read the list of phases and
interfacial models and coefficients from the
'constant/<region>/phaseProperties' dictionary.
Backward-compatibility is provided by the solvers reading
'thermophysicalProperties' or 'transportProperties' if the 'phaseProperties'
dictionary does not exist. For incompressible VoF solvers the
'transportProperties' is automatically upgraded to 'phaseProperties' and the
two 'physicalProperties.<phase>' dictionary for the phase properties.
* viscosity
Abstract base-class (interface) for all fluids.
Having a single interface for the viscosity of all types of fluids facilitated
a substantial simplification of the 'momentumTransport' library, avoiding the
need for a layer of templating and providing total consistency between
incompressible/compressible and single-phase/multi-phase laminar, RAS and LES
momentum transport models. This allows the generalised Newtonian viscosity
models to be used in the same form within laminar as well as RAS and LES
momentum transport closures in any solver. Strain-rate dependent viscosity
modelling is particularly useful with low-Reynolds number turbulence closures
for non-Newtonian fluids where the effect of bulk shear near the walls on the
viscosity is a dominant effect. Within this framework it would also be
possible to implement generalised Newtonian models dependent on turbulent as
well as mean strain-rate if suitable model formulations are available.
* visosityModel
Run-time selectable Newtonian viscosity model for incompressible fluids
providing the 'viscosity' interface for 'momentumTransport' models.
Currently a 'constant' Newtonian viscosity model is provided but the structure
supports more complex functions of time, space and fields registered to the
region database.
Strain-rate dependent non-Newtonian viscosity models have been removed from
this level and handled in a more general way within the 'momentumTransport'
library, see section 'viscosity' above.
The 'constant' viscosity model is selected in the 'physicalProperties'
dictionary by
viscosityModel constant;
which is equivalent to the previous entry in the 'transportProperties'
dictionary
transportModel Newtonian;
but backward-compatibility is provided for both the keyword and model
type.
* thermophysicalModels
To avoid propagating the unnecessary constructors from 'dictionary' into the
new 'physicalProperties' abstract base-class this entire structure has been
removed from the 'thermophysicalModels' library. The only use for this
constructor was in 'thermalBaffle' which now reads the 'physicalProperties'
dictionary from the baffle region directory which is far simpler and more
consistent and significantly reduces the amount of constructor code in the
'thermophysicalModels' library.
* compressibleInterFoam
The creation of the 'viscosity' interface for the 'momentumTransport' models
allows the complex 'twoPhaseMixtureThermo' derived from 'rhoThermo' to be
replaced with the much simpler 'compressibleTwoPhaseMixture' derived from the
'viscosity' interface, avoiding the myriad of unused thermodynamic functions
required by 'rhoThermo' to be defined for the mixture.
Same for 'compressibleMultiphaseMixture' in 'compressibleMultiphaseInterFoam'.
This is a significant improvement in code and input consistency, simplifying
maintenance and further development as well as enhancing usability.
Henry G. Weller
CFD Direct Ltd.
splitBaffles identifies baffle faces; i.e., faces on the mesh boundary
which share the exact same set of points as another boundary face. It
then splits the points to convert these faces into completely separate
boundary patches. This functionality was previously provided by calling
mergeOrSplitBaffles with the "-split" option.
mergeBaffles also identifes the duplicate baffle faces, but then merges
them, converting them into a single set of internal faces. This
functionality was previously provided by calling mergeOrSplitBaffles
without the "-split" option.
When using 'simple' or 'hierarchical' decomposition it is useful to slightly rotate a
coordinate-aligned block-mesh to improve the processor boundaries by avoiding
irregular cell distribution at those boundaries. The degree of slight rotation
is controlled by the 'delta' coefficient and a value of 0.001 is generally
suitable so to avoid unnecessary clutter in 'decomposeParDict' 'delta' now
defaults to this value.
The FOAM file format has not changed from version 2.0 in many years and so there
is no longer a need for the 'version' entry in the FoamFile header to be
required and to reduce unnecessary clutter it is now optional, defaulting to the
current file format 2.0.
The pressure work term for total internal energy is div(U p) which can be
discretised is various ways, given a mass flux field phi it seems logical to
implement it in the form div(phi/interpolate(rho), p) but this is not exactly
consistent with the relationship between enthalpy and internal energy (h = e +
p/rho) and the transport of enthalpy, it would be more consistent to implement
it in the form div(phi, p/rho). A further improvement in consistency can be
gained by using the same convection scheme for this work term and the convection
term div(phi, e) and for reacting solvers this is easily achieved by using the
multi-variate limiter mvConvection provided for energy and specie convection.
This more consistent total internal energy work term has now been implemented in
all the compressible and reacting flow solvers and provides more accurate
solutions when running with internal energy, particularly for variable density
mixing cases with small pressure variation.
For non-reacting compressible solvers this improvement requires a change to the
corresponding divScheme in fvSchemes:
div(phiv,p) -> div(phi,(p|rho))
and all the tutorials have been updated accordingly.
This makes usage of transformPoints the same as for
surfaceTransformPoints. Transformations are supplied as a string and are
applied in sequence.
Usage
transformPoints "\<transformations\>" [OPTION]
Supported transformations:
- "translate=<translation vector>"
Translational transformation by given vector
- "rotate=(<n1 vector> <n2 vector>)"
Rotational transformation from unit vector n1 to n2
- "Rx=<angle [deg] about x-axis>"
Rotational transformation by given angle about x-axis
- "Ry=<angle [deg] about y-axis>"
Rotational transformation by given angle about y-axis
- "Rz=<angle [deg] about z-axis>"
Rotational transformation by given angle about z-axis
- "Ra=<axis vector> <angle [deg] about axis>"
Rotational transformation by given angle about given axis
- "scale=<x-y-z scaling vector>"
Anisotropic scaling by the given vector in the x, y, z
coordinate directions
Example usage:
transformPoints \
"translate=(-0.05 -0.05 0), \
Rz=45, \
translate=(0.05 0.05 0)"
To provide more flexibility, extensibility, run-time modifiability and
consistency the handling of optional pressure limits has been moved from
pressureControl (settings in system/fvSolution) to the new limitPressure
fvConstraint (settings in system/fvConstraints).
All tutorials have been updated which provides guidance when upgrading cases but
also helpful error messages are generated for cases using the old settings
providing specific details as to how the case should be updated, e.g. for the
tutorials/compressible/rhoSimpleFoam/squareBend case which has the pressure
limit specification:
SIMPLE
{
...
pMinFactor 0.1;
pMaxFactor 2;
...
generates the error message
--> FOAM FATAL IO ERROR:
Pressure limits should now be specified in fvConstraints:
limitp
{
type limitPressure;
minFactor 0.1;
maxFactor 2;
}
file: /home/dm2/henry/OpenFOAM/OpenFOAM-dev/tutorials/compressible/rhoSimpleFoam/squareBend/system/fvSolution/SIMPLE from line 41 to line 54.
The new fvModels is a general interface to optional physical models in the
finite volume framework, providing sources to the governing conservation
equations, thus ensuring consistency and conservation. This structure is used
not only for simple sources and forces but also provides a general run-time
selection interface for more complex models such as radiation and film, in the
future this will be extended to Lagrangian, reaction, combustion etc. For such
complex models the 'correct()' function is provided to update the state of these
models at the beginning of the PIMPLE loop.
fvModels are specified in the optional constant/fvModels dictionary and
backward-compatibility with fvOption is provided by reading the
constant/fvOptions or system/fvOptions dictionary if present.
The new fvConstraints is a general interface to optional numerical constraints
applied to the matrices of the governing equations after construction and/or to
the resulting field after solution. This system allows arbitrary changes to
either the matrix or solution to ensure numerical or other constraints and hence
violates consistency with the governing equations and conservation but it often
useful to ensure numerical stability, particularly during the initial start-up
period of a run. Complex manipulations can be achieved with fvConstraints, for
example 'meanVelocityForce' used to maintain a specified mean velocity in a
cyclic channel by manipulating the momentum matrix and the velocity solution.
fvConstraints are specified in the optional system/fvConstraints dictionary and
backward-compatibility with fvOption is provided by reading the
constant/fvOptions or system/fvOptions dictionary if present.
The separation of fvOptions into fvModels and fvConstraints provides a rational
and consistent separation between physical and numerical models which is easier
to understand and reason about, avoids the confusing issue of location of the
controlling dictionary file, improves maintainability and easier to extend to
handle current and future requirements for optional complex physical models and
numerical constraints.
A number of fvOptions that apply to a user-derined field can now
automatically work what primitive type they apply to. These options can
apply to any field type, and in some cases even multiple fields of
differing type. Example usage of the options to which this change
applies are shown below:
codedSource1
{
type codedSource;
name codedSource1;
field h;
...
}
fixedValueConstraint1
{
type fixedValueConstraint;
fieldValues
{
R (1 0 0 1 0 1);
epsilon 150;
}
...
}
phaseLimitStabilization11
{
type phaseLimitStabilization;
field sigma.liquid;
...
}
Previously to apply to a given type, these options had to be selected
with the name of the type prepended to the option name (e.g., "type
symmTensorPhaseLimitStabilization;") and those that operated on multiple
fields were restricted to those fields being of the same type.
A number of other options have had improvements made to their handling
of user specification of fields. Where possible, the option will now
attempt to work out what field the option applies to automatically. The
following options, therefore, no longer require "field" or "fields"
entries:
actuationDiskSource
buoyancyEnergy
buoyancyForce
meanVelocityForce
rotorDiskSource
volumeFractionSource
constantHeatTransfer
function2HeatTransfer
variableHeatTransfer
Non-standard field names can be overridden in the same way as in
boundary conditions; e.g., the velocity name can be overridden with a "U
<UName>;" entry if it does not have the default name, "U". The name of
the energy field is now always determined from the thermodynamics
model and should always be correct. Some options that can be applied to
an individual phase also support a "phase <phaseName>;" entry;
fvOptions field-name handling has been rewritten to increase its
flexibility and to improve warning messages. The flexibility now allows
for options that apply to all fields, or all fields of a given phase,
rather than being limited to a specific list of field names. Messages
warning about options that have not been applied now always print just
once per time-step.
Originally the only supported geometry specification were triangulated surfaces,
hence the name of the directory: constant/triSurface, however now that other
surface specifications are supported and provided it is much more logical that
the directory is named accordingly: constant/geometry. All tutorial and
template cases have been updated.
Note that backward compatibility is provided such that if the constant/geometry
directory does not exist but constant/triSurface does then the geometry files
are read from there.
It is better to not select and instantiate a model, fvOption etc. than to create
it and set it inactive as the creation process requires reading of settings,
parameters, fields etc. with all the associated specification and storage
without being used. Also the incomplete implementation added a lot of
complexity in the low-level operation of models introducing a significant
maintenance overhead and development overhead for new models.
Most fvOptions change the state of the fields and equations they are applied to
but do not change internal state so it makes more sense that the interface is
const, consistent with MeshObjects. For the few fvOptions which do maintain a
changing state the member data is now mutable.
The new optional 'slash' scoping syntax is now the default and provides a more
intuitive and flexible syntax than the previous 'dot' syntax, corresponding to
the common directory/file access syntax used in UNIX, providing support for
reading entries from other dictionary files.
In the 'slash' syntax
'/' is the scope operator
'../' is the parent dictionary scope operator
'!' is the top-level dictionary scope operator
Examples:
internalField 3.4;
active
{
type fixedValue;
value.air $internalField;
}
inactive
{
type anotherFixedValue;
value $../active/value.air;
anotherValue $!active/value.air;
sub
{
value $../../active/value.air;
anotherValue $!active/value.air;
}
}
"U.*"
{
solver GAMG;
}
e.air
{
$U.air;
}
external
{
value $testSlashDict2!active/value.air;
}
active2
{
$testSlashDict2!active;
}
If there is a part of the keyword before the '!' then this is taken to be the
file name of the dictionary from which the entry will be looked-up using the
part of the keyword after the '!'. For example given a file testSlashDict containing
internalField 5.6;
active
{
type fixedValue;
value.air $internalField;
}
entries from it can be read directly from another file, e.g.
external
{
value $testSlashDict2!active/value.air;
}
active2
{
$testSlashDict2!active;
}
which expands to
external
{
value 5.6;
}
active2
{
type fixedValue;
value.air 5.6;
}
These examples are provided in applications/test/dictionary.
The the default syntax can be changed from 'slash' to 'dot' in etc/controlDict
to revert to the previous behaviour:
OptimisationSwitches
{
.
.
.
// Default dictionary scoping syntax
inputSyntax slash; // Change to dot for previous behaviour
}
or within a specific dictionary by adding the entry
See applications/test/dictionary/testDotDict.
All models that require templating on the thermodynamic model, including
the thermodynamic models themselves, are now instantiated using a
centralised set of variadic macros. Seven macros exist to instantiate
models for different classes of thermodynamics model. These are:
forGases: All model combinations valid for gases
forCommonGases: The most commonly used gas models
forAbsoluteGases: A limited selection of gas models with absolute
forms of energy, for use with Xi-combustion models
forLiquids: All model combinations valid for liquids
forCommonLiquids: The most commonly used liquid models
forPolynomials: Model combinations with properties fitted to
polynomials
forSolids: All model combinations valid for solids
All the *ThermoPhysics typedefs have been removed, as this system was
fundamentally not extensible. The enormous lists of thermodynamic
instantiations that existed for reaction thermos, chemistry models,
tabulation methods, etc..., were extremely difficult to read and reason
about what combinations are valid under what circumstances. This change
centralises those decisions, makes them concise and readable, and makes
them consistent across the entire codebase.
Soot model selection has now been brought up to date in line with
chemistry, combustion, and others. The angle-bracketed part of the name
is no longer necessary; this information is determined directly from the
existing thermo model. So, now to select a mixture-fraction soot model,
the entry is simply:
sootModel mixtureFraction;
Rather than:
sootModel mixtureFraction<rhoReactionThermo,gasHThermoPhysics>;
The only place in which *ThermoPhysics typedefs are still required in
the selection name is in the thermalBaffle1D boundary condition. Here
there is no thermo model from which to determine a name. This eventually
needs resolving either by adding a selection mechanism similar to that
of the thermo packages themselves, or by removing this boundary
condition in favour of the (non-1D) thermal baffle boundary condition
and region model.
