This fixes a consistency issue in the interface-composition method, and
also seems to improve stability/convergence of the pimple iteration in
the presence of significant mass transfer.
Now lnInclude are created as required by the presence of entries in the EXE_INC
variable in the Make/options file. This removes the need for calling
wmakeLnInclude in various Allwmake files to ensure the existence of the
lnInclude directories prior to compilation of dependent libraries.
Added a function object for the reacting Euler-Euler solvers which
evaluates and writes out the blended interfacial forces acting on a
given phase (drag, virtual mass, lift, wall lubrication and turbulent
dispersion).
Patch contributed by Institute of Fluid Dynamics, Helmholtz-Zentrum
Dresden - Rossendorf (HZDR)
The Sauter mean diameter calculation has been modified to be more stable
in the limit of vanishing phase fraction. The calculation of the overall
Sauter mean diameter for a populationBalance involving more than one
velocityGroup has been removed. This calculation depends upon the phase
fraction and it is not stable as the fractions tend to zero. The overall
Sauter mean diameter is only used for post-processing and can still be
recovered from the individual diameter fields of the involved
velocityGroups.
Some parts of the population balance modeling have also been renamed and
refactored.
Patch contributed by Institute of Fluid Dynamics, Helmholtz-Zentrum
Dresden - Rossendorf (HZDR)
The calculations for mixture rho and U have been changed so that they
represent phase-averaged quantities over the moving phases only.
The mixture density is used as part of the pressure solution to
calculate buoyancy forces. The pressure within a stationary phase is
considered to be decoupled from the moving phases; i.e., it is
considered self-supporting. Therefore the stationary phase density
should not form a part of buoyancy calculations. This change to the
definition of mixture density ensures this.
Lookup of models associated with unordered phase pairs now searches for
both possible pair names; e.g. gasAndLiquid and liquidAndGas.
Patch contributed by Institute of Fluid Dynamics, Helmholtz-Zentrum
Dresden - Rossendorf (HZDR)
The nonRandomTwoLiquid and Roult interface composition models have been
instantiated (and updated so that they compile), and a fuller set of
multi-component liquids and multi-component and reacting gases have been
used.
The selection name of the saturated and nonRandomTwoLiquid models have
also been changed to remove the capitalisation from the first letter, as
is consistent with other sub-models that are not proper nouns.
This model transfers a dispersed droplet phase to a film phase at a rate
relative to its intersection with a third phase. The third phase is
termed the "surface". It can be enabled in constant/phaseProperties as
follows:
phaseTransfer
(
(droplets and film)
{
type deposition;
droplet droplets;
surface solid;
efficiency 0.1;
}
);
The efficiency is an empirical factor which represents a reduction in
collisions as a result of droplets flowing around the surface phase and
not coalescing on impact.
This work was supported by Georg Skillas and Zhen Li, at Evonik
An additional layer has been added into the phase system hierarchy which
facilitates the application of phase transfer modelling. These are
models which exchange mass between phases without the thermal coupling
that would be required to represent phase change. They can be thought of
as representation changes; e.g., between two phases representing
different droplet sizes of the same physical fluid.
To facilitate this, the heat transfer phase systems have been modified
and renamed and now both support mass transfer. The two sided version
is only required for derivations which support phase change.
The following changes to case settings have been made:
- The simplest instantiated phase systems have been renamed to
basicTwoPhaseSystem and basicMultiphaseSystem. The
heatAndMomentumTransfer*System entries in constant/phaseProperties files
will need updating accordingly.
- A phaseTransfer sub-model entry will be required in the
constant/phaseProperties file. This can be an empty list.
- The massTransfer switch in thermal phase change cases has been renamed
phaseTransfer, so as not to be confused with the mass transfer models
used by interface composition cases.
This work was supported by Georg Skillas and Zhen Li, at Evonik
Blended models are now registered and can be looked up in the same way
as regular interfacial models via the phaseSystem::lookupSubModel
method. For example, to access the blended drag model, the following
code could be used:
const BlendedInterfacialModel<dragModel>& drag =
fluid.lookupSubModel<BlendedInterfacialModel<dragModel>>
(
phasePair(gas, liquid)
);
Here, "fluid" is the phase system, and "gas" and "liquid" are the phase
models between which the blended drag model applies.
Also added tutorial case demonstrating usage. Note that the new drag
models are symmetric and should be used without any blending.
This work was supported by Georg Skillas and Zhen Li, at Evonik
Two new phase models have been added as selectable options for
reactingMultiphaseEulerFoam; pureStationaryPhaseModel and
pureStationaryIsothermalPhaseModel. These phases do not store a
velocity and their phase fractions remain constant throughout the
simulation. They are intended for use in modelling static particle beds
and other forms of porous media by means of the existing Euler-Euler
transfer models (drag, heat transfer, etc...).
Note that this functionality has not been extended to
reactingTwoPhaseEulerFoam, or the non-reacting *EulerFoam solvers.
Additional maintenance work has been carried out on the phase model
and phase system structure. The system can now loop over subsets of
phases with specific functionality (moving, multi-component, etc...) in
order to avoid testing for the existence of equations or variables in
the top level solver. The mass transfer handling and it's effect on
per-phase source terms has been refactored to reduce duplication. Const
and non-const access to phase properties has been formalised by renaming
non-const accessors with a "Ref" suffix, which is consistent with other
recent developments to classes including tmp and GeometricField, among
others. More sub-modelling details have been made private in order to
reduce the size of interfaces and improve abstraction.
This work was supported by Zhen Li, at Evonik
MULES and CMULES have been extended so that the limits can be supplied
as fields. These arguments are templated so that zeroField, oneField or
UniformField<scalar> can be used in place of a scalar value with no
additional overhead. The flux argument has been removed from the
unlimited CMULES correct functions in order to make this templating
possible.
An additional form of limit sum has also been added to MULES. This
limits the flux sum by ofsetting in proportion to the phase fraction,
rather than by reducing the magnitude of the fluxes with the same sign
as the imbalance. The new procedure makes it possible to limit the flux
sum in the presence of constraints without encountering a divide by
zero.
Partial elimination has been implemented for the multiphase Euler-Euler
solver. This does a linear solution of the drag system when calculating
flux and velocity corrections after the solution of the pressure
equation. This can improve the behaviour of the solution in the event
that the drag coupling is high. It is controlled by means of a
"partialElimination" switch within the PIMPLE control dictionary in
fvSolution.
A re-organisation has also been done in order to remove the exposure of
the sub-modelling from the top-level solver. Rather than looping the
drag, virtual mass, lift, etc..., models directly, the solver now calls
a set of phase-system methods which group the different force terms.
These new methods are documented in MomentumTransferPhaseSystem.H. Many
other accessors have been removed as a consequence of this grouping.
A bug was also fixed whereby the face-based algorithm was not
transferring the momentum associated with a given interfacial mass
transfer.
