Settings for the individual non-conformal couples can now be put in a
"nonConformalCouples" sub-dictionary of the
system/createNonConformalCouplesDict. For example:
fields no;
nonConformalCouples // <-- new sub-dictionary
{
nonConformalCouple_none
{
patches (nonCouple1 nonCouple2);
transform none;
}
nonConformalCouple_30deg
{
patches (nonCoupleBehind nonCoupleAhead);
transform rotational;
rotationAxis (-1 0 0);
rotationCentre (0 0 0);
rotationAngle 30;
}
}
This permits settings to be #include-d from files that themselves
contain sub-dictionaries without the utility treating those
sub-dictionaries as if they specify a non-conformal coupling. It also
makes the syntax more comparable to that of createBafflesDict.
The new "nonConformalCouples" sub-dictionary is optional, so this change
is backwards compatible. The new syntax is recommended, however, and all
examples have been changed accordingly.
This utility now always creates two patches, and only creates duplicate
faces when they connect to different cells and point in opposite
directions. Now that ACMI has been removed, there is no need to create
duplicate faces on the same cell and with similar orientations. This is
unituitive and is now considered an invalid mesh topology.
The preferred syntax for createBaffles is now as follows:
internalFacesOnly true;
baffles
{
cyclics
{
type faceZone;
zoneName cyclicFaces;
owner
{
name cyclicLeft;
type cyclic;
neighbourPatch cyclicRight;
}
neighbour
{
name cyclicRight;
type cyclic;
neighbourPatch cyclicLeft;
}
}
}
Note that the 'patches' sub-dictionary is not needed any more; the
'owner' and 'neighbour' sub-dictionaries can be in the same dictionary
as the parameters with which faces are selected. For backwards
compatibility, however, a 'patches' sub-dictionary is still permitted,
as are keywords 'master' and 'slave' (in place of 'owner' and
'neighbour', respectively).
The 'patchPairs' syntax has been removed. Whilst consise, this syntax
made a number of assumptions and decisions regarding naming conventions
that were not sufficiently intuitive for the user to understand without
extensive reference to the code. If identical boundaries are desired on
both sides of the patch, dictionary substitution provides a more
intuitive way of minimising the amount of specifiection required. For
example, to create two back-to-back walls, the following specification
could be used:
internalFacesOnly true;
fields true;
baffles
{
walls
{
type faceZone;
zoneName wallFaces;
owner
{
name baffleWallLeft;
type wall;
patchFields
{
p
{
type zeroGradient;
}
U
{
type noSlip;
}
}
}
neighbour
{
name baffleWallRight;
$owner; // <-- Use the same settings as for the owner
}
}
}
Mesh motion and topology change are now combinable run-time selectable options
within fvMesh, replacing the restrictive dynamicFvMesh which supported only
motion OR topology change.
All solvers which instantiated a dynamicFvMesh now instantiate an fvMesh which
reads the optional constant/dynamicFvMeshDict to construct an fvMeshMover and/or
an fvMeshTopoChanger. These two are specified within the optional mover and
topoChanger sub-dictionaries of dynamicFvMeshDict.
When the fvMesh is updated the fvMeshTopoChanger is first executed which can
change the mesh topology in anyway, adding or removing points as required, for
example for automatic mesh refinement/unrefinement, and all registered fields
are mapped onto the updated mesh. The fvMeshMover is then executed which moved
the points only and calculates the cell volume change and corresponding
mesh-fluxes for conservative moving mesh transport. If multiple topological
changes or movements are required these would be combined into special
fvMeshMovers and fvMeshTopoChangers which handle the processing of a list of
changes, e.g. solidBodyMotionFunctions:multiMotion.
The tutorials/multiphase/interFoam/laminar/sloshingTank3D3DoF case has been
updated to demonstrate this new functionality by combining solid-body motion
with mesh refinement/unrefinement:
/*--------------------------------*- C++ -*----------------------------------*\
========= |
\\ / F ield | OpenFOAM: The Open Source CFD Toolbox
\\ / O peration | Website: https://openfoam.org
\\ / A nd | Version: dev
\\/ M anipulation |
\*---------------------------------------------------------------------------*/
FoamFile
{
format ascii;
class dictionary;
location "constant";
object dynamicMeshDict;
}
// * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * //
mover
{
type motionSolver;
libs ("libfvMeshMovers.so" "libfvMotionSolvers.so");
motionSolver solidBody;
solidBodyMotionFunction SDA;
CofG (0 0 0);
lamda 50;
rollAmax 0.2;
rollAmin 0.1;
heaveA 4;
swayA 2.4;
Q 2;
Tp 14;
Tpn 12;
dTi 0.06;
dTp -0.001;
}
topoChanger
{
type refiner;
libs ("libfvMeshTopoChangers.so");
// How often to refine
refineInterval 1;
// Field to be refinement on
field alpha.water;
// Refine field in between lower..upper
lowerRefineLevel 0.001;
upperRefineLevel 0.999;
// Have slower than 2:1 refinement
nBufferLayers 1;
// Refine cells only up to maxRefinement levels
maxRefinement 1;
// Stop refinement if maxCells reached
maxCells 200000;
// Flux field and corresponding velocity field. Fluxes on changed
// faces get recalculated by interpolating the velocity. Use 'none'
// on surfaceScalarFields that do not need to be reinterpolated.
correctFluxes
(
(phi none)
(nHatf none)
(rhoPhi none)
(alphaPhi.water none)
(meshPhi none)
(meshPhi_0 none)
(ghf none)
);
// Write the refinement level as a volScalarField
dumpLevel true;
}
// ************************************************************************* //
Note that currently this is the only working combination of mesh-motion with
topology change within the new framework and further development is required to
update the set of topology changers so that topology changes with mapping are
separated from the mesh-motion so that they can be combined with any of the
other movements or topology changes in any manner.
All of the solvers and tutorials have been updated to use the new form of
dynamicMeshDict but backward-compatibility was not practical due to the complete
reorganisation of the mesh change structure.
for consistency with the regionToCell topo set source and splitMeshRegions and
provides more logical extension to the multiple and outside point variants insidePoints,
outsidePoint and outsidePoints.
The FOAM file format has not changed from version 2.0 in many years and so there
is no longer a need for the 'version' entry in the FoamFile header to be
required and to reduce unnecessary clutter it is now optional, defaulting to the
current file format 2.0.
The inside or outside region refinement level is now specified using the simple
"level <level>" entry in refinementRegions e.g.
refinementRegions
{
refinementBox
{
mode inside;
level 5;
}
}
rather than
refinementRegions
{
refinementBox
{
mode inside;
levels ((1E15 5));
}
}
where the spurious "1E15" number is not used and the '((...))' is unnecessary clutter.
The new fvModels is a general interface to optional physical models in the
finite volume framework, providing sources to the governing conservation
equations, thus ensuring consistency and conservation. This structure is used
not only for simple sources and forces but also provides a general run-time
selection interface for more complex models such as radiation and film, in the
future this will be extended to Lagrangian, reaction, combustion etc. For such
complex models the 'correct()' function is provided to update the state of these
models at the beginning of the PIMPLE loop.
fvModels are specified in the optional constant/fvModels dictionary and
backward-compatibility with fvOption is provided by reading the
constant/fvOptions or system/fvOptions dictionary if present.
The new fvConstraints is a general interface to optional numerical constraints
applied to the matrices of the governing equations after construction and/or to
the resulting field after solution. This system allows arbitrary changes to
either the matrix or solution to ensure numerical or other constraints and hence
violates consistency with the governing equations and conservation but it often
useful to ensure numerical stability, particularly during the initial start-up
period of a run. Complex manipulations can be achieved with fvConstraints, for
example 'meanVelocityForce' used to maintain a specified mean velocity in a
cyclic channel by manipulating the momentum matrix and the velocity solution.
fvConstraints are specified in the optional system/fvConstraints dictionary and
backward-compatibility with fvOption is provided by reading the
constant/fvOptions or system/fvOptions dictionary if present.
The separation of fvOptions into fvModels and fvConstraints provides a rational
and consistent separation between physical and numerical models which is easier
to understand and reason about, avoids the confusing issue of location of the
controlling dictionary file, improves maintainability and easier to extend to
handle current and future requirements for optional complex physical models and
numerical constraints.
Originally the only supported geometry specification were triangulated surfaces,
hence the name of the directory: constant/triSurface, however now that other
surface specifications are supported and provided it is much more logical that
the directory is named accordingly: constant/geometry. All tutorial and
template cases have been updated.
Note that backward compatibility is provided such that if the constant/geometry
directory does not exist but constant/triSurface does then the geometry files
are read from there.
It is better to not select and instantiate a model, fvOption etc. than to create
it and set it inactive as the creation process requires reading of settings,
parameters, fields etc. with all the associated specification and storage
without being used. Also the incomplete implementation added a lot of
complexity in the low-level operation of models introducing a significant
maintenance overhead and development overhead for new models.
The new optional 'slash' scoping syntax is now the default and provides a more
intuitive and flexible syntax than the previous 'dot' syntax, corresponding to
the common directory/file access syntax used in UNIX, providing support for
reading entries from other dictionary files.
In the 'slash' syntax
'/' is the scope operator
'../' is the parent dictionary scope operator
'!' is the top-level dictionary scope operator
Examples:
internalField 3.4;
active
{
type fixedValue;
value.air $internalField;
}
inactive
{
type anotherFixedValue;
value $../active/value.air;
anotherValue $!active/value.air;
sub
{
value $../../active/value.air;
anotherValue $!active/value.air;
}
}
"U.*"
{
solver GAMG;
}
e.air
{
$U.air;
}
external
{
value $testSlashDict2!active/value.air;
}
active2
{
$testSlashDict2!active;
}
If there is a part of the keyword before the '!' then this is taken to be the
file name of the dictionary from which the entry will be looked-up using the
part of the keyword after the '!'. For example given a file testSlashDict containing
internalField 5.6;
active
{
type fixedValue;
value.air $internalField;
}
entries from it can be read directly from another file, e.g.
external
{
value $testSlashDict2!active/value.air;
}
active2
{
$testSlashDict2!active;
}
which expands to
external
{
value 5.6;
}
active2
{
type fixedValue;
value.air 5.6;
}
These examples are provided in applications/test/dictionary.
The the default syntax can be changed from 'slash' to 'dot' in etc/controlDict
to revert to the previous behaviour:
OptimisationSwitches
{
.
.
.
// Default dictionary scoping syntax
inputSyntax slash; // Change to dot for previous behaviour
}
or within a specific dictionary by adding the entry
See applications/test/dictionary/testDotDict.
Following the generalisation of the TurbulenceModels library to support
non-Newtonian laminar flow including visco-elasticity and extensible to other
form of non-Newtonian behaviour the name TurbulenceModels is misleading and does
not properly represent how general the OpenFOAM solvers now are. The
TurbulenceModels now provides an interface to momentum transport modelling in
general and the plan is to rename it MomentumTransportModels and in preparation
for this the turbulenceProperties dictionary has been renamed momentumTransport
to properly reflect its new more general purpose.
The old turbulenceProperties name is supported for backward-compatibility.
snappyHexMesh produces a far better quality AMI interface using a cylindrical background mesh,
leading to much more robust performance, even on a relatively coarse mesh. The min/max AMI
weights remain close to 1 as the mesh moves, giving better conservation.
The rotating geometry template cases are configured with a blockMeshDict file for a cylindrical
background mesh aligned along the z-axis. The details of use are found in the README and
blockMeshDict files.
so that the specification of the name and dimensions are optional in property dictionaries.
Update tutorials so that the name of the dimensionedScalar property is
no longer duplicated but optional dimensions are still provided and are
checked on read.
The templates include a stategy to simplify meshing with snappyHexMesh,
particularly to help generate an initial mesh quickly that can subsequently be
improved. The templates are setup to enable rapid initial simulations, typically
with simpleFoam. The initial templates cover simple inflow-outflow and closed
domains, including rotating geometry, and an example axisymmetric flow. For
more details, consult the README file accompanying each template case.
The cases are located in $FOAM_ETC/templates
