87bce82854
The calculation and input/output of transformations has been rewritten
for all coupled patches. This replaces multiple duplicated, inconsistent
and incomplete implementations of transformation handling which were
spread across the different coupled patch types.
Transformations are now calculated or specified once, typically during
mesh construction or manipulation, and are written out with the boundary
data. They are never re-calculated. Mesh changes should not change the
transformation across a coupled interface; to do so would violate the
transformation.
Transformations are now calculated using integral properties of the
patches. This is more numerically stable that the previous methods which
functioned in terms of individual faces. The new routines are also able
to automatically calculate non-zero centres of rotation.
The user input of transformations is backwards compatible, and permits
the user to manually specify varying amounts of the transformation
geometry. Anything left unspecified gets automatically computed from the
patch geometry. Supported specifications are:
1) No specification. Transformations on cyclics are automatically
generated, and cyclicAMI-type patches assume no transformation. For
example (in system/blockMeshDict):
cyclicLeft
{
type cyclic;
neighbourPatch cyclicRight;
faces ((0 1 2 3));
}
cyclicRight
{
type cyclic;
neighbourPatch cyclicLeft;
faces ((4 5 6 7));
}
2) Partial specification. The type of transformation is specified
by the user, as well as the coordinate system if the transform is
rotational. The rotation angle or separation vector is still
automatically generated. This form is useful as the signs of the
angle and separation are opposite on different sides of an interface
and can be difficult to specify correctly. For example:
cyclicLeft
{
type cyclic;
neighbourPatch cyclicRight;
transformType translational;
faces ((0 1 2 3));
}
cyclicRight
{
type cyclic;
neighbourPatch cyclicLeft;
transformType translational;
faces ((4 5 6 7));
}
cyclicAMILeft
{
type cyclicAMI;
neighbourPatch cyclicAMIRight;
transformType rotational;
rotationAxis (0 0 1);
rotationCentre (0.05 -0.01 0);
faces ((8 9 10 11));
}
cyclicAMIRight
{
type cyclicAMI;
neighbourPatch cyclicAMILeft;
transformType rotational;
rotationAxis (0 0 1);
rotationCentre (0.05 -0.01 0);
faces ((12 13 14 15));
}
3) Full specification. All parameters of the transformation are
given. For example:
cyclicLeft
{
type cyclic;
neighbourPatch cyclicRight;
transformType translational;
separaion (-0.01 0 0);
faces ((0 1 2 3));
}
cyclicRight
{
type cyclic;
neighbourPatch cyclicLeft;
transformType translational;
separaion (0.01 0 0);
faces ((4 5 6 7));
}
cyclicAMILeft
{
type cyclicAMI;
neighbourPatch cyclicAMIRight;
transformType rotational;
rotationAxis (0 0 1);
rotationCentre (0.05 -0.01 0);
rotationAngle 60;
faces ((8 9 10 11));
}
cyclicAMIRight
{
type cyclicAMI;
neighbourPatch cyclicAMILeft;
transformType rotational;
rotationAxis (0 0 1);
rotationCentre (0.05 -0.01 0);
rotationAngle 60;
faces ((12 13 14 15));
}
Automatic ordering of faces and points across coupled patches has also
been rewritten, again replacing multiple unsatisfactory implementations.
The new ordering method is more robust on poor meshes as it
geometrically matches only a single face (per contiguous region of the
patch) in order to perform the ordering, and this face is chosen to be
the one with the highest quality. A failure in ordering now only occurs
if the best face in the patch cannot be geometrically matched, whether
as previously the worst face could cause the algorithm to fail.
The oldCyclicPolyPatch has been removed, and the mesh converters which
previously used it now all generate ordered cyclic and baffle patches
directly. This removes the need to run foamUpgradeCyclics after
conversion. In addition the fluent3DMeshToFoam converter now supports
conversion of periodic/shadow pairs to OpenFOAM cyclic patches.
README for OpenFOAM-dev
- About OpenFOAM
- Copyright
- Download and installation instructions
- Documentation
- Source code documentation
- OpenFOAM C++ Style Guide
- Reporting bugs in OpenFOAM
- Contacting the OpenFOAM Foundation
#
About OpenFOAM
OpenFOAM is a free, open source computational fluid dynamics (CFD) software package released by the OpenFOAM Foundation. It has a large user base across most areas of engineering and science, from both commercial and academic organisations. OpenFOAM has an extensive range of features to solve anything from complex fluid flows involving chemical reactions, turbulence and heat transfer, to solid dynamics and electromagnetics.
Copyright
OpenFOAM is free software: you can redistribute it and/or modify it under the
terms of the GNU General Public License as published by the Free Software
Foundation, either version 3 of the License, or (at your option) any later
version. See the file COPYING in this directory or
http://www.gnu.org/licenses/, for a description of the GNU General Public
License terms under which you can copy the files.