For example the porosity coefficients may now be specified thus:
porosity1
{
type DarcyForchheimer;
cellZone porosity;
d (5e7 -1000 -1000);
f (0 0 0);
coordinateSystem
{
type cartesian;
origin (0 0 0);
coordinateRotation
{
type axesRotation;
e1 (0.70710678 0.70710678 0);
e2 (0 0 1);
}
}
}
rather than
porosity1
{
type DarcyForchheimer;
active yes;
cellZone porosity;
DarcyForchheimerCoeffs
{
d (5e7 -1000 -1000);
f (0 0 0);
coordinateSystem
{
type cartesian;
origin (0 0 0);
coordinateRotation
{
type axesRotation;
e1 (0.70710678 0.70710678 0);
e2 (0 0 1);
}
}
}
}
support for which is maintained for backward compatibility.
For example the actuationDiskSource fvOption may now be specified
disk1
{
type actuationDiskSource;
fields (U);
selectionMode cellSet;
cellSet actuationDisk1;
diskDir (1 0 0); // Orientation of the disk
Cp 0.386;
Ct 0.58;
diskArea 40;
upstreamPoint (581849 4785810 1065);
}
rather than
disk1
{
type actuationDiskSource;
active on;
actuationDiskSourceCoeffs
{
fields (U);
selectionMode cellSet;
cellSet actuationDisk1;
diskDir (1 0 0); // Orientation of the disk
Cp 0.386;
Ct 0.58;
diskArea 40;
upstreamPoint (581849 4785810 1065);
}
}
but this form is supported for backward compatibility.
Main changes in the tutorial:
- General cleanup of the phaseProperties of unnecessary entries
- sensibleEnthalpy is used for both phases
- setTimeStep functionObject is used to set a sharp reduction in time step near the start of the injection
- Monitoring of pressure minimum and maximum
Patch contributed by Juho Peltola, VTT.
The standard naming convention for heat flux is "q" and this is used for the
conductive and convective heat fluxes is OpenFOAM. The use of "Qr" for
radiative heat flux is an anomaly which causes confusion, particularly for
boundary conditions in which "Q" is used to denote power in Watts. The name of
the radiative heat flux has now been corrected to "qr" and all models, boundary
conditions and tutorials updated.
Description
Temperature-dependent surface tension model in which the surface tension
function provided by the phase Foam::liquidProperties class is used.
Usage
\table
Property | Description | Required | Default value
phase | Phase name | yes |
\endtable
Example of the surface tension specification:
\verbatim
sigma
{
type liquidProperties;
phase water;
}
\endverbatim
for use with e.g. compressibleInterFoam, see
tutorials/multiphase/compressibleInterFoam/laminar/depthCharge2D
These models have been particularly designed for use in the VoF solvers, both
incompressible and compressible. Currently constant and temperature dependent
surface tension models are provided but it easy to write models in which the
surface tension is evaluated from any fields held by the mesh database.
Demonstrates meshing a cylinder with hemispehrical ends using snappyHexMesh with
a polar background mesh that uses the point and edge projection feature of blockMesh.
The case prescribes a multiMotion on the cylinder, combining an oscillatingLinearMotion
and transverse rotatingMotion.
The pitzDaily case uses a lot of mesh grading close to walls and the shear layer.
Prior to v2.4, blockMesh only permitted grading in one direction within a single block,
so the pitzDaily mesh comprised of 13 blocks to accommodate the complex grading pattern.
blockMesh has multi-grading that allows users to divide a block in a given direction and
apply different grading within each division. The mesh generated with blockMesh using
13 blocks has been replaced with a mesh of 5 blocks that use multi-grading. The new
blockMeshDict configuration produces a mesh very similar to the original 13-block mesh.
including support for TDAC and ISAT for efficient chemistry calculation.
Description
Eddy Dissipation Concept (EDC) turbulent combustion model.
This model considers that the reaction occurs in the regions of the flow
where the dissipation of turbulence kinetic energy takes place (fine
structures). The mass fraction of the fine structures and the mean residence
time are provided by an energy cascade model.
There are many versions and developments of the EDC model, 4 of which are
currently supported in this implementation: v1981, v1996, v2005 and
v2016. The model variant is selected using the optional \c version entry in
the \c EDCCoeffs dictionary, \eg
\verbatim
EDCCoeffs
{
version v2016;
}
\endverbatim
The default version is \c v2015 if the \c version entry is not specified.
Model versions and references:
\verbatim
Version v2005:
Cgamma = 2.1377
Ctau = 0.4083
kappa = gammaL^exp1 / (1 - gammaL^exp2),
where exp1 = 2, and exp2 = 2.
Magnussen, B. F. (2005, June).
The Eddy Dissipation Concept -
A Bridge Between Science and Technology.
In ECCOMAS thematic conference on computational combustion
(pp. 21-24).
Version v1981:
Changes coefficients exp1 = 3 and exp2 = 3
Magnussen, B. (1981, January).
On the structure of turbulence and a generalized
eddy dissipation concept for chemical reaction in turbulent flow.
In 19th Aerospace Sciences Meeting (p. 42).
Version v1996:
Changes coefficients exp1 = 2 and exp2 = 3
Gran, I. R., & Magnussen, B. F. (1996).
A numerical study of a bluff-body stabilized diffusion flame.
Part 2. Influence of combustion modeling and finite-rate chemistry.
Combustion Science and Technology, 119(1-6), 191-217.
Version v2016:
Use local constants computed from the turbulent Da and Re numbers.
Parente, A., Malik, M. R., Contino, F., Cuoci, A., & Dally, B. B.
(2016).
Extension of the Eddy Dissipation Concept for
turbulence/chemistry interactions to MILD combustion.
Fuel, 163, 98-111.
\endverbatim
Tutorials cases provided: reactingFoam/RAS/DLR_A_LTS, reactingFoam/RAS/SandiaD_LTS.
This codes was developed and contributed by
Zhiyi Li
Alessandro Parente
Francesco Contino
from BURN Research Group
and updated and tested for release by
Henry G. Weller
CFD Direct Ltd.
Using
decomposePar -copyZero
The mesh is decomposed as usual but the '0' directory is recursively copied to
the 'processor.*' directories rather than decomposing the fields. This is a
convenient option to handle cases where the initial field files are generic and
can be used for serial or parallel running. See for example the
incompressible/simpleFoam/motorBike tutorial case.
Both stardard SIMPLE and the SIMPLEC (using the 'consistent' option in
fvSolution) are now supported for both subsonic and transonic flow of all
fluid types.
rhoPimpleFoam now instantiates the lower-level fluidThermo which instantiates
either a psiThermo or rhoThermo according to the 'type' specification in
thermophysicalProperties, see also commit 655fc78748
Both stardard SIMPLE and the SIMPLEC (using the 'consistent' option in
fvSolution) are now supported for both subsonic and transonic flow of all
fluid types.
rhoSimpleFoam now instantiates the lower-level fluidThermo which instantiates
either a psiThermo or rhoThermo according to the 'type' specification in
thermophysicalProperties, e.g.
thermoType
{
type hePsiThermo;
mixture pureMixture;
transport sutherland;
thermo janaf;
equationOfState perfectGas;
specie specie;
energy sensibleInternalEnergy;
}
instantiates a psiThermo for a perfect gas with JANAF thermodynamics, whereas
thermoType
{
type heRhoThermo;
mixture pureMixture;
properties liquid;
energy sensibleInternalEnergy;
}
mixture
{
H2O;
}
instantiates a rhoThermo for water, see new tutorial
compressible/rhoSimpleFoam/squareBendLiq.
In order to support complex equations of state the pressure can no longer be
unlimited and rhoSimpleFoam now limits the pressure rather than the density to
handle start-up more robustly.
For backward compatibility 'rhoMin' and 'rhoMax' can still be used in the SIMPLE
sub-dictionary of fvSolution which are converted into 'pMax' and 'pMin' but it
is better to set either 'pMax' and 'pMin' directly or use the more convenient
'pMinFactor' and 'pMinFactor' from which 'pMax' and 'pMin' are calculated using
the fixed boundary pressure or reference pressure e.g.
SIMPLE
{
nNonOrthogonalCorrectors 0;
pMinFactor 0.1;
pMaxFactor 1.5;
transonic yes;
consistent yes;
residualControl
{
p 1e-3;
U 1e-4;
e 1e-3;
"(k|epsilon|omega)" 1e-3;
}
}
This allows single, multi-phase and VoF compressible simulations to be performed
with the accurate thermophysical property functions for liquids provided by the
liquidProperty classes. e.g. in the
multiphase/compressibleInterFoam/laminar/depthCharge2D tutorial water can now be
specified by
thermoType
{
type heRhoThermo;
mixture pureMixture;
properties liquid;
energy sensibleInternalEnergy;
}
mixture
{
H2O;
}
as an alternative to the previous less accurate representation defined by
thermoType
{
type heRhoThermo;
mixture pureMixture;
transport const;
thermo hConst;
equationOfState perfectFluid;
specie specie;
energy sensibleInternalEnergy;
}
mixture
{
specie
{
molWeight 18.0;
}
equationOfState
{
R 3000;
rho0 1027;
}
thermodynamics
{
Cp 4195;
Hf 0;
}
transport
{
mu 3.645e-4;
Pr 2.289;
}
}
However the increase in accuracy of the new simpler and more convenient
specification and representation comes at a cost: the NSRDS functions used by
the liquidProperties classes are relatively expensive to evaluate and the
depthCharge2D case takes ~14% longer to run.
The entries for liquid and solid species can now be simply be the name unless
property coefficients are overridden in which are specified in a dictionary as
before e.g. in the tutorials/lagrangian/coalChemistryFoam/simplifiedSiwek case
the water is simply specified
liquids
{
H2O;
}
and solid ash uses standard coefficients but the coefficients for carbon are
overridden thus
solids
{
C
{
rho 2010;
Cp 710;
kappa 0.04;
Hf 0;
emissivity 1.0;
}
ash;
}
The defaultCoeffs entry is now redundant and supported only for backward
compatibility. To specify a liquid with default coefficients simply leave the
coefficients dictionary empty:
liquids
{
H2O {}
}
Any or all of the coefficients may be overridden by specifying the properties in
the coefficients dictionary, e.g.
liquids
{
H2O
{
rho
{
a 1000;
b 0;
c 0;
d 0;
}
}
}
The fundamental properties provided by the specie class hierarchy were
mole-based, i.e. provide the properties per mole whereas the fundamental
properties provided by the liquidProperties and solidProperties classes are
mass-based, i.e. per unit mass. This inconsistency made it impossible to
instantiate the thermodynamics packages (rhoThermo, psiThermo) used by the FV
transport solvers on liquidProperties. In order to combine VoF with film and/or
Lagrangian models it is essential that the physical propertied of the three
representations of the liquid are consistent which means that it is necessary to
instantiate the thermodynamics packages on liquidProperties. This requires
either liquidProperties to be rewritten mole-based or the specie classes to be
rewritten mass-based. Given that most of OpenFOAM solvers operate
mass-based (solve for mass-fractions and provide mass-fractions to sub-models it
is more consistent and efficient if the low-level thermodynamics is also
mass-based.
This commit includes all of the changes necessary for all of the thermodynamics
in OpenFOAM to operate mass-based and supports the instantiation of
thermodynamics packages on liquidProperties.
Note that most users, developers and contributors to OpenFOAM will not notice
any difference in the operation of the code except that the confusing
nMoles 1;
entries in the thermophysicalProperties files are no longer needed or used and
have been removed in this commet. The only substantial change to the internals
is that species thermodynamics are now "mixed" with mass rather than mole
fractions. This is more convenient except for defining reaction equilibrium
thermodynamics for which the molar rather than mass composition is usually know.
The consequence of this can be seen in the adiabaticFlameT, equilibriumCO and
equilibriumFlameT utilities in which the species thermodynamics are
pre-multiplied by their molecular mass to effectively convert them to mole-basis
to simplify the definition of the reaction equilibrium thermodynamics, e.g. in
equilibriumCO
// Reactants (mole-based)
thermo FUEL(thermoData.subDict(fuelName)); FUEL *= FUEL.W();
// Oxidant (mole-based)
thermo O2(thermoData.subDict("O2")); O2 *= O2.W();
thermo N2(thermoData.subDict("N2")); N2 *= N2.W();
// Intermediates (mole-based)
thermo H2(thermoData.subDict("H2")); H2 *= H2.W();
// Products (mole-based)
thermo CO2(thermoData.subDict("CO2")); CO2 *= CO2.W();
thermo H2O(thermoData.subDict("H2O")); H2O *= H2O.W();
thermo CO(thermoData.subDict("CO")); CO *= CO.W();
// Product dissociation reactions
thermo CO2BreakUp
(
CO2 == CO + 0.5*O2
);
thermo H2OBreakUp
(
H2O == H2 + 0.5*O2
);
Please report any problems with this substantial but necessary rewrite of the
thermodynamic at https://bugs.openfoam.org
Henry G. Weller
CFD Direct Ltd.
Now the interFoam and compressibleInterFoam families of solvers use the same
alphaEqn formulation and supporting all of the MULES options without
code-duplication.
The semi-implicit MULES support allows running with significantly larger
time-steps but this does reduce the interface sharpness.
By default snappyHexMesh writes files relating to the hex-splitting process into
the polyMesh directory: cellLevel level0Edge pointLevel surfaceIndex
but by setting the noRefinement flag:
writeFlags
(
noRefinement
.
.
.
);
these optional files which are generally not needed are not written.
If you run the three stages of snappyHexMesh separately or run a dynamic mesh
solver supporting refinement and unrefinement these files are needed
and "noRefinement" should not be set.
Avoids slight phase-fraction unboundedness at entertainment BCs and improved
robustness.
Additionally the phase-fractions in the multi-phase (rather than two-phase)
solvers are adjusted to avoid the slow growth of inconsistency ("drift") caused
by solving for all of the phase-fractions rather than deriving one from the
others.
New reactingFoam tutorial counterFlowFlame2DLTS_GRI_TDAC demonstrates this new
functionality.
Additionally the ISAT table growth algorithm has been further optimized
providing an overall speedup of between 15% and 38% for the tests run so far.
Updates to TDAC and ISAT provided by Francesco Contino.
Implementation updated and integrated into OpenFOAM-dev by
Henry G. Weller, CFD Direct Ltd with the help of Francesco Contino.
Original code providing all algorithms for chemistry reduction and
tabulation contributed by Francesco Contino, Tommaso Lucchini, Gianluca
D’Errico, Hervé Jeanmart, Nicolas Bourgeois and Stéphane Backaert.
e.g. in tutorials/heatTransfer/buoyantSimpleFoam/externalCoupledCavity/0/T
hot
{
type externalCoupledTemperature;
commsDir "${FOAM_CASE}/comms";
file "data";
initByExternal yes;
log true;
value uniform 307.75; // 34.6 degC
}
Previously both 'file' and 'fileName' were used inconsistently in different
classes and given that there is no confusion or ambiguity introduced by using
the simpler 'file' rather than 'fileName' this change simplifies the use and
maintenance of OpenFOAM.
e.g. the motion of two counter-rotating AMI regions could be defined:
dynamicFvMesh dynamicMotionSolverListFvMesh;
solvers
(
rotor1
{
solver solidBody;
cellZone rotor1;
solidBodyMotionFunction rotatingMotion;
rotatingMotionCoeffs
{
origin (0 0 0);
axis (0 0 1);
omega 6.2832; // rad/s
}
}
rotor2
{
solver solidBody;
cellZone rotor2;
solidBodyMotionFunction rotatingMotion;
rotatingMotionCoeffs
{
origin (0 0 0);
axis (0 0 1);
omega -6.2832; // rad/s
}
}
);
Any combination of motion solvers may be selected but there is no special
handling of motion interaction; the motions are applied sequentially and
potentially cumulatively.
To support this new general framework the solidBodyMotionFvMesh and
multiSolidBodyMotionFvMesh dynamicFvMeshes have been converted into the
corresponding motionSolvers solidBody and multiSolidBody and the tutorials
updated to reflect this change e.g. the motion in the mixerVesselAMI2D tutorial
is now defined thus:
dynamicFvMesh dynamicMotionSolverFvMesh;
solver solidBody;
solidBodyCoeffs
{
cellZone rotor;
solidBodyMotionFunction rotatingMotion;
rotatingMotionCoeffs
{
origin (0 0 0);
axis (0 0 1);
omega 6.2832; // rad/s
}
}
New functionality contributed by Mattijs Janssens:
- new edge projection: projectCurve for use with new geometry
'searchableCurve'
- new tutorial 'pipe'
- naming of vertices and blocks (see pipe tutorial). Including back
substitution for error messages.
