The sampled sets have been renamed in a more explicit and consistent
manner, and two new ones have also been added. The available sets are as
follows:
arcUniform: Uniform samples along an arc. Replaces "circle", and
adds the ability to sample along only a part of the circle's
circumference. Example:
{
type arcUniform;
centre (0.95 0 0.25);
normal (1 0 0);
radial (0 0 0.25);
startAngle -1.57079633;
endAngle 0.52359878;
nPoints 200;
axis x;
}
boundaryPoints: Specified point samples associated with a subset of
the boundary. Replaces "patchCloud". Example:
{
type boundaryPoints;
patches (inlet1 inlet2);
points ((0 -0.05 0.05) (0 -0.05 0.1) (0 -0.05 0.15));
maxDistance 0.01;
axis x;
}
boundaryRandom: Random samples within a subset of the boundary.
Replaces "patchSeed", but changes the behaviour to be entirely
random. It does not seed the boundary face centres first. Example:
{
type boundaryRandom;
patches (inlet1 inlet2);
nPoints 1000;
axis x;
}
boxUniform: Uniform grid of samples within a axis-aligned box.
Replaces "array". Example:
{
type boxUniform;
box (0.95 0 0.25) (1.2 0.25 0.5);
nPoints (2 4 6);
axis x;
}
circleRandom: Random samples within a circle. New. Example:
{
type circleRandom;
centre (0.95 0 0.25);
normal (1 0 0);
radius 0.25;
nPoints 200;
axis x;
}
lineFace: Face-intersections along a line. Replaces "face". Example:
{
type lineFace;
start (0.6 0.6 0.5);
end (0.6 -0.3 -0.1);
axis x;
}
lineCell: Cell-samples along a line at the mid-points in-between
face-intersections. Replaces "midPoint". Example:
{
type lineCell;
start (0.5 0.6 0.5);
end (0.5 -0.3 -0.1);
axis x;
}
lineCellFace: Combination of "lineFace" and "lineCell". Replaces
"midPointAndFace". Example:
{
type lineCellFace;
start (0.55 0.6 0.5);
end (0.55 -0.3 -0.1);
axis x;
}
lineUniform: Uniform samples along a line. Replaces "uniform".
Example:
{
type lineUniform;
start (0.65 0.3 0.3);
end (0.65 -0.3 -0.1);
nPoints 200;
axis x;
}
points: Specified points. Replaces "cloud" when the ordered flag is
false, and "polyLine" when the ordered flag is true. Example:
{
type points;
points ((0 -0.05 0.05) (0 -0.05 0.1) (0 -0.05 0.15));
ordered yes;
axis x;
}
sphereRandom: Random samples within a sphere. New. Example:
{
type sphereRandom;
centre (0.95 0 0.25);
radius 0.25;
nPoints 200;
axis x;
}
triSurfaceMesh: Samples from all the points of a triSurfaceMesh.
Replaces "triSurfaceMeshPointSet". Example:
{
type triSurfaceMesh;
surface "surface.stl";
axis x;
}
The headers have also had documentation added. Example usage and a
description of the control parameters now exists for all sets.
In addition, a number of the algorithms which generate the sets have
been refactored or rewritten. This was done either to take advantage of
the recent changes to random number generation, or to remove ad-hoc
fixes that were made unnecessary by the barycentric tracking algorithm.
including third-body and pressure dependent derivatives, and derivative of the
temperature term. The complete Jacobian is more robust than the incomplete and
partially approximate form used previously and improves the efficiency of the
stiff ODE solvers which rely on the Jacobian.
Reaction rate evaluation moved from the chemistryModel to specie library to
simplfy support for alternative reaction rate expressions and associated
Jacobian terms.
Temperature clipping included in the Reaction class. This is inactive by default
but for most cases it is advised to provide temperature limits (high and
low). These are provided in the foamChemistryFile with the keywords Thigh and
Tlow. When using chemkinToFoam these values are set to the limits of the Janaf
thermodynamic data. With the new Jacobian this temperature clipping has proved
very beneficial for stability and for some cases essential.
Improvement of the TDAC MRU list better integrated in add and grow functions.
To get the most out of this significant development it is important to re-tune
the ODE integration tolerances, in particular the absTol in the odeCoeffs
sub-dictionary of the chemistryProperties dictionary:
odeCoeffs
{
solver seulex;
absTol 1e-12;
relTol 0.01;
}
Typically absTol can now be set to 1e-8 and relTol to 0.1 except for ignition
time problems, and with theses settings the integration is still robust but for
many cases a lot faster than previously.
Code development and integration undertaken by
Francesco Contino
Henry G. Weller, CFD Direct
runApplication isn't needed for foamDictionary as it doesn't log
anything of consequence. Using runApplication leads to false unconfirmed
completion warnings in the test loop as foamDictionary does not generate
an end statement.
The changeDictonary setup has been removed and replaced with a more
typical boundary condition setup. Dictionary variables and wildcards
have been used to reduce repetition of the simulation parameters.
The tutorial now also demonstrates how to run a multi-region CHT case
completely in parallel. If run-time post processing was being utilised
there would be no need for reconstruction at any point.
A new constraint patch has been added which permits AMI coupling in
cyclic geometries. The coupling is repeated with different multiples of
the cyclic transformation in order to achieve a full correspondence.
This allows, for example, a cylindrical AMI interface to be used in a
sector of a rotational geometry.
The patch is used in a similar manner to cyclicAMI, except that it has
an additional entry, "transformPatch". This entry must name a coupled
patch. The transformation used to repeat the AMI coupling is taken from
this patch. For example, in system/blockMeshDict:
boundary
(
cyclic1
{
type cyclic;
neighbourPatch cyclic2;
faces ( ... );
}
cyclic2
{
type cyclic;
neighbourPatch cyclic1;
faces ( ... );
}
cyclicRepeatAMI1
{
type cyclicRepeatAMI;
neighbourPatch cyclicRepeatAM2;
transformPatch cyclic1;
faces ( ... );
}
cyclicRepeatAMI2
{
type cyclicRepeatAMI;
neighbourPatch cyclicRepeatAMI1;
transformPatch cyclic1;
faces ( ... );
}
// other patches ...
);
In this example, the transformation between cyclic1 and cyclic2 is used
to define the repetition used by the two cyclicRepeatAMI patches.
Whether cyclic1 or cyclic2 is listed as the transform patch is not
important.
A tutorial, incompressible/pimpleFoam/RAS/impeller, has been added to
demonstrate the functionality. This contains two repeating AMI pairs;
one cylindrical and one planar.
A significant amount of maintenance has been carried out on the AMI and
ACMI patches as part of this work. The AMI methods now return
dimensionless weights by default, which prevents ambiguity over the
units of the weight field during construction. Large amounts of
duplicate code have also been removed by deriving ACMI classes from
their AMI equivalents. The reporting and writing of AMI weights has also
been unified.
This work was supported by Dr Victoria Suponitsky, at General Fusion
Surfaces are specified as a list and the controls applied to each, e.g. in the
rhoPimpleFoam/RAS/annularThermalMixer tutorial:
surfaces
(
"AMI.obj"
"shaft.obj"
"wall.obj"
"statorBlades.obj"
"rotorBlades.obj"
);
includedAngle 150; // Identifes a feature when angle
// between faces < includedAngle
trimFeatures
{
minElem 10; // minimum edges within a feature
}
writeObj yes; // writes out _edgeMesh.obj files to view features
If different controls are required for different surfaces multiple
sub-dictionaries can be used:
AMIsurfaces
{
surfaces
(
"AMI.obj"
);
includedAngle 140; // Identifes a feature when angle
// between faces < includedAngle
trimFeatures
{
minElem 8; // minimum edges within a feature
}
writeObj yes; // writes out _edgeMesh.obj files to view features
}
otherSurfaces
{
surfaces
(
"shaft.obj"
"wall.obj"
"statorBlades.obj"
"rotorBlades.obj"
);
includedAngle 150; // Identifes a feature when angle
// between faces < includedAngle
trimFeatures
{
minElem 10; // minimum edges within a feature
}
writeObj yes; // writes out _edgeMesh.obj files to view features
}
Existing feature edge files corresponding to particular surfaces can be specified using
the "files" association list:
surfaces
(
"AMI.obj"
"shaft.obj"
"wall.obj"
"statorBlades.obj"
"rotorBlades.obj"
);
files
(
"AMI.obj" "constant/triSurface/AMI.obj.eMesh";
);
includedAngle 150; // Identifes a feature when angle
// between faces < includedAngle
trimFeatures
{
minElem 10; // minimum edges within a feature
}
writeObj yes; // writes out _edgeMesh.obj files to view features
