diff --git a/tutorials/compressible/rhoCentralFoam/biconic25-55Run35/Allrun b/tutorials/compressible/rhoCentralFoam/biconic25-55Run35/Allrun
index ca832252d8..abde516d9c 100755
--- a/tutorials/compressible/rhoCentralFoam/biconic25-55Run35/Allrun
+++ b/tutorials/compressible/rhoCentralFoam/biconic25-55Run35/Allrun
@@ -20,7 +20,7 @@ runApplication datToFoam grid256.dat
 
 CONST="constant"
 cat $CONST/pointsHeader $CONST/points.tmp > $CONST/polyMesh/points
-runApplication collapseEdges "2e-07" 5
+runApplication collapseEdges
 moveTimeMeshToConstant
 
 echo "Changing patch type to wedge type in boundary file"
diff --git a/tutorials/compressible/rhoCentralFoam/biconic25-55Run35/system/collapseDict b/tutorials/compressible/rhoCentralFoam/biconic25-55Run35/system/collapseDict
new file mode 100644
index 0000000000..95602e9516
--- /dev/null
+++ b/tutorials/compressible/rhoCentralFoam/biconic25-55Run35/system/collapseDict
@@ -0,0 +1,84 @@
+/*--------------------------------*- C++ -*----------------------------------*\
+| =========                 |                                                 |
+| \\      /  F ield         | OpenFOAM: The Open Source CFD Toolbox           |
+|  \\    /   O peration     | Version:  dev                                   |
+|   \\  /    A nd           | Web:      www.OpenFOAM.org                      |
+|    \\/     M anipulation  |                                                 |
+\*---------------------------------------------------------------------------*/
+FoamFile
+{
+    version     2.0;
+    format      ascii;
+    class       dictionary;
+    object      collapseDict;
+}
+// * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * //
+
+collapseEdgesCoeffs
+{
+    // Edges shorter than this absolute value will be merged
+    minimumEdgeLength   2e-7;
+
+    // The maximum angle between two edges that share a point attached to
+    // no other edges
+    maximumMergeAngle   5;
+
+    // The amount that minimumEdgeLength will be reduced by for each
+    // edge if that edge's collapse generates a poor quality face
+    reductionFactor     0.5;
+}
+
+
+collapseFacesCoeffs
+{
+    // The initial face length factor
+    initialFaceLengthFactor                 0.5;
+
+    // The amount that initialFaceLengthFactor will be reduced by for each
+    // face if its collapse generates a poor quality face
+    reductionFactor                         $initialFaceLengthFactor;
+
+    // If the face can't be collapsed to an edge, and it has a span less than
+    // the target face length multiplied by this coefficient, collapse it
+    // to a point.
+    maxCollapseFaceToPointSideLengthCoeff   0.3;
+
+    // Allow early collapse of edges to a point
+    allowEarlyCollapseToPoint               on;
+
+    // Fraction to premultiply maxCollapseFaceToPointSideLengthCoeff by if
+    // allowEarlyCollapseToPoint is enabled
+    allowEarlyCollapseCoeff                 0.2;
+
+    // Defining how close to the midpoint (M) of the projected
+    // vertices line a projected vertex (X) can be before making this
+    // an invalid edge collapse
+    //
+    // X---X-g----------------M----X-----------g----X--X
+    //
+    // Only allow a collapse if all projected vertices are outwith
+    // guardFraction (g) of the distance form the face centre to the
+    // furthest vertex in the considered direction
+    guardFraction                           0.1;
+}
+
+
+meshQualityCoeffs
+{
+    // Name of the dictionary that has the mesh quality coefficients used
+    // by motionSmoother::checkMesh
+    #include                    "meshQualityDict";
+
+    // Maximum number of smoothing iterations for the reductionFactors
+    maximumSmoothingIterations  2;
+
+    // Maximum number of outer iterations is mesh quality checking is enabled
+    maximumIterations           10;
+
+    // Maximum number of iterations deletion of a point can cause a bad face
+    // to be constructed before it is forced to not be deleted
+    maxPointErrorCount          5;
+}
+
+
+// ************************************************************************* //
diff --git a/tutorials/compressible/rhoCentralFoam/biconic25-55Run35/system/meshQualityDict b/tutorials/compressible/rhoCentralFoam/biconic25-55Run35/system/meshQualityDict
new file mode 100644
index 0000000000..d6228d0abd
--- /dev/null
+++ b/tutorials/compressible/rhoCentralFoam/biconic25-55Run35/system/meshQualityDict
@@ -0,0 +1,67 @@
+/*--------------------------------*- C++ -*----------------------------------*\
+| =========                 |                                                 |
+| \\      /  F ield         | OpenFOAM: The Open Source CFD Toolbox           |
+|  \\    /   O peration     | Version:  dev                                   |
+|   \\  /    A nd           | Web:      http://www.openfoam.org               |
+|    \\/     M anipulation  |                                                 |
+\*---------------------------------------------------------------------------*/
+FoamFile
+{
+    version         2.0;
+    format          ascii;
+    class           dictionary;
+    object          meshQualityDict;
+}
+// * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * //
+
+//- Maximum non-orthogonality allowed. Set to 180 to disable.
+maxNonOrtho         180;
+
+//- Max skewness allowed. Set to <0 to disable.
+maxBoundarySkewness 50;
+
+//- Max skewness allowed. Set to <0 to disable.
+maxInternalSkewness 10;
+
+//- Max concaveness allowed. Is angle (in degrees) below which concavity
+//  is allowed. 0 is straight face, <0 would be convex face.
+//  Set to 180 to disable.
+maxConcave          80;
+
+//- Minimum pyramid volume. Is absolute volume of cell pyramid.
+//  Set to a sensible fraction of the smallest cell volume expected.
+//  Set to very negative number (e.g. -1E30) to disable.
+minVol              1e-20;
+
+//- Minimum quality of the tet formed by the face-centre
+//  and variable base point minimum decomposition triangles and
+//  the cell centre. This has to be a positive number for tracking
+//  to work. Set to very negative number (e.g. -1E30) to
+//  disable.
+//     <0 = inside out tet,
+//      0 = flat tet
+//      1 = regular tet
+minTetQuality       1e-30;
+
+//- Minimum face area. Set to <0 to disable.
+minArea             -1;
+
+//- Minimum face twist. Set to <-1 to disable. dot product of face normal
+//- and face centre triangles normal
+minTwist            0.0;
+
+//- minimum normalised cell determinant
+//- 1 = hex, <= 0 = folded or flattened illegal cell
+minDeterminant      0.001;
+
+//- minFaceWeight (0 -> 0.5)
+minFaceWeight       0.02;
+
+//- minVolRatio (0 -> 1)
+minVolRatio         0.01;
+
+//must be >0 for Fluent compatibility
+minTriangleTwist    -1;
+
+
+// ************************************************************************* //