autoRefineMesh: corrected source file and executable names

applications/utilities/mesh/advanced/autoRefineMesh/autoRefineMeshDict

@@ -0,0 +1,112 @@
+/*--------------------------------*- C++ -*----------------------------------*\
+| =========                 |                                                 |
+| \\      /  F ield         | OpenFOAM: The Open Source CFD Toolbox           |
+|  \\    /   O peration     | Version:  dev                                   |
+|   \\  /    A nd           | Web:      www.OpenFOAM.org                      |
+|    \\/     M anipulation  |                                                 |
+\*---------------------------------------------------------------------------*/
+FoamFile
+{
+    version     2.0;
+    format      ascii;
+    class       dictionary;
+    object      snappyRefineMeshDict;
+}
+// * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * //
+
+// Surface to keep to
+surface         "plexi.obj";
+
+// What is outside. These points have to be inside a cell (so not on a face!)
+outsidePoints   ((-0.99001 -0.99001 -0.99001));
+
+//
+// Selection of cells to refine
+//
+
+// If smallest edge of mesh > maxEdgeLen select all cut cells for refinement.
+// If < maxEdgeLen select only those cut cells which are closer than
+// curvatureDistance to surface
+// and with cos of angle between normals on surface < curvature.
+maxEdgeLen          0.1;
+curvatureDistance   1.0;
+curvature           0.9;
+
+// if > 0: Remove inside cells at every step. Inside is given by number of
+// layers separating outside from inside.
+// (note that we cannot remove outside
+// cells since these contain the outsidePoints)
+// Do not use this option if you want mesh to spill through a hole which is
+// not visible on the coarsest level but only becomes visible after refinement
+nCutLayers 2;
+
+// Refine until smallest edge of mesh < minEdgeLen
+minEdgeLen      0.1;
+
+// Or until the number of cells would become more than (stops one level before
+// this)
+cellLimit       2500000;
+
+//
+// Selection of final set
+//
+
+// Select based on side of surface. Usually select inside cells and project
+// outwards or select outside cells and project inwards.
+selectCut       false;
+selectInside    false;
+selectOutside   true;
+// Leave out cell closer than nearDistance to the surface. Usually
+// 0.5*minEdgeLen. Set to -1 to disable.
+nearDistance    -1;
+
+// Some cells on the surface of the selected cells might have all their
+// points on the 'outside'. These would get flattened when projecting so
+// are either kept and refined (selectHanging) or removed from the set
+selectHanging   false;
+
+//
+// Refinement parameters
+//
+
+// Type of coordinate system
+coordinateSystem global;
+//coordinateSystem patchLocal;
+
+// .. and its coefficients. x,y in this case. (normal = tan1^tan2)
+globalCoeffs
+{
+    tan1 (1 0 0);
+    tan2 (0 1 0);
+}
+
+patchLocalCoeffs
+{
+    patch outside;  // Normal direction is facenormal of zero'th face of patch
+    tan1 (1 0 0);
+
+}
+
+// List of directions to refine
+directions
+(
+    tan1
+    tan2
+    normal
+);
+
+// refinement level difference between neighbouring cells. Set to large if
+// there is no need for a limit.
+splitLevel      2;
+
+// Cut purely geometric (will cut hexes through vertices) or take topology
+// into account.
+geometricCut    false;
+
+// Whether to use hex topology. This will never cut hex through vertices.
+useHexTopology  yes;
+
+// Write meshes from intermediate steps
+writeMesh       true;
+
+// ************************************************************************* //