For example the actuationDiskSource fvOption may now be specified
disk1
{
type actuationDiskSource;
fields (U);
selectionMode cellSet;
cellSet actuationDisk1;
diskDir (1 0 0); // Orientation of the disk
Cp 0.386;
Ct 0.58;
diskArea 40;
upstreamPoint (581849 4785810 1065);
}
rather than
disk1
{
type actuationDiskSource;
active on;
actuationDiskSourceCoeffs
{
fields (U);
selectionMode cellSet;
cellSet actuationDisk1;
diskDir (1 0 0); // Orientation of the disk
Cp 0.386;
Ct 0.58;
diskArea 40;
upstreamPoint (581849 4785810 1065);
}
}
but this form is supported for backward compatibility.
Main changes in the tutorial:
- General cleanup of the phaseProperties of unnecessary entries
- sensibleEnthalpy is used for both phases
- setTimeStep functionObject is used to set a sharp reduction in time step near the start of the injection
- Monitoring of pressure minimum and maximum
Patch contributed by Juho Peltola, VTT.
- This can be used as a convenient alternative to comparing against end().
Eg,
dictionaryConstructorTable::iterator cstrIter =
dictionaryConstructorTablePtr_->find(methodType);
if (cstrIter.found())
{
...
}
vs.
if (cstrIter != dictionaryConstructorTablePtr_->end())
{
...
}
- 1st problem arises when there are edges, but edgeNormals is empty.
The UIndirectList fails (zero elements, non-zero addressing)
- further problem occurs if there is a mismatch in the number of edges
and edges normals (incorrect indexing on loop).
The standard naming convention for heat flux is "q" and this is used for the
conductive and convective heat fluxes is OpenFOAM. The use of "Qr" for
radiative heat flux is an anomaly which causes confusion, particularly for
boundary conditions in which "Q" is used to denote power in Watts. The name of
the radiative heat flux has now been corrected to "qr" and all models, boundary
conditions and tutorials updated.
by combining with and rationalizing functionality from
turbulentHeatFluxTemperatureFvPatchScalarField.
externalWallHeatFluxTemperatureFvPatchScalarField now replaces
turbulentHeatFluxTemperatureFvPatchScalarField which is no longer needed and has
been removed.
Description
This boundary condition applies a heat flux condition to temperature
on an external wall in one of three modes:
- fixed power: supply Q
- fixed heat flux: supply q
- fixed heat transfer coefficient: supply h and Ta
where:
\vartable
Q | Power [W]
q | Heat flux [W/m^2]
h | Heat transfer coefficient [W/m^2/K]
Ta | Ambient temperature [K]
\endvartable
For heat transfer coefficient mode optional thin thermal layer resistances
can be specified through thicknessLayers and kappaLayers entries.
The thermal conductivity \c kappa can either be retrieved from various
possible sources, as detailed in the class temperatureCoupledBase.
Usage
\table
Property | Description | Required | Default value
mode | 'power', 'flux' or 'coefficient' | yes |
Q | Power [W] | for mode 'power' |
q | Heat flux [W/m^2] | for mode 'flux' |
h | Heat transfer coefficient [W/m^2/K] | for mode 'coefficent' |
Ta | Ambient temperature [K] | for mode 'coefficient' |
thicknessLayers | Layer thicknesses [m] | no |
kappaLayers | Layer thermal conductivities [W/m/K] | no |
qr | Name of the radiative field | no | none
qrRelaxation | Relaxation factor for radiative field | no | 1
kappaMethod | Inherited from temperatureCoupledBase | inherited |
kappa | Inherited from temperatureCoupledBase | inherited |
\endtable
Example of the boundary condition specification:
\verbatim
<patchName>
{
type externalWallHeatFluxTemperature;
mode coefficient;
Ta uniform 300.0;
h uniform 10.0;
thicknessLayers (0.1 0.2 0.3 0.4);
kappaLayers (1 2 3 4);
kappaMethod fluidThermo;
value $internalField;
}
\endverbatim
- can be useful with compiling additional OpenFOAM programs
that use FOAM_USER_APPBIN, FOAM_USER_LIBBIN for their build,
to avoid conflicts with the normal user bin/lib files.
- or to force relocation of FOAM_SITE_APPBIN, FOAM_SITE_LIBBIN
during packaging of OpenFOAM
Description
Temperature-dependent surface tension model in which the surface tension
function provided by the phase Foam::liquidProperties class is used.
Usage
\table
Property | Description | Required | Default value
phase | Phase name | yes |
\endtable
Example of the surface tension specification:
\verbatim
sigma
{
type liquidProperties;
phase water;
}
\endverbatim
for use with e.g. compressibleInterFoam, see
tutorials/multiphase/compressibleInterFoam/laminar/depthCharge2D
- just check WM_PROJECT_DIR instead.
- provide a fallback value when FOAM_EXT_LIBBIN might actually be needed.
Only strictly need FOAM_EXT_LIBBIN for scotch/metis decomposition, and
when these are actually supplied by ThirdParty.
All other ThirdParty dependencies are referenced by BOOST_ARCH_PATH etc.
Can therefore drop the FOAM_EXT_LIBBIN dependency for VTK-related
things, which do not use scotch/metis anyhow.
snappyHexMesh produces a far better quality AMI interface using a cylindrical background mesh,
leading to much more robust performance, even on a relatively coarse mesh. The min/max AMI
weights remain close to 1 as the mesh moves, giving better conservation.
The rotating geometry template cases are configured with a blockMeshDict file for a cylindrical
background mesh aligned along the z-axis. The details of use are found in the README and
blockMeshDict files.
Uncommenting the patches provides a convenient way to use the patches in the background mesh
to define the external boundary of the final mesh. Replaces previous setup with a separate
blockMeshDict.extPatches file.
- this implies that jobControl is a user-resource for OpenFOAM.
It was previously located under $WM_PROJECT_INST_DIR/jobControl,
but few users will have write access there.
- an unset FOAM_JOB_DIR variable is treated as "~/.OpenFOAM/jobControl",
which can partially reduce environment clutter.
- provide argList::noJobInfo() to conveniently suppress job-info on an
individual basis for short-running utilities (eg, foamListTimes) to
avoid unneeded clutter.
These models have been particularly designed for use in the VoF solvers, both
incompressible and compressible. Currently constant and temperature dependent
surface tension models are provided but it easy to write models in which the
surface tension is evaluated from any fields held by the mesh database.
