Resolves bug-report https://bugs.openfoam.org/view.php?id=2785
ENH: compressibleInterFoam family: merged two-phase momentum stress modelling from compressibleInterPhaseTransportFoam
The new momentum stress model selector class
compressibleInterPhaseTransportModel is now used to select between the options:
Description
Transport model selection class for the compressibleInterFoam family of
solvers.
By default the standard mixture transport modelling approach is used in
which a single momentum stress model (laminar, non-Newtonian, LES or RAS) is
constructed for the mixture. However if the \c simulationType in
constant/turbulenceProperties is set to \c twoPhaseTransport the alternative
Euler-Euler two-phase transport modelling approach is used in which separate
stress models (laminar, non-Newtonian, LES or RAS) are instantiated for each
of the two phases allowing for different modeling for the phases.
Mixture and two-phase momentum stress modelling is now supported in
compressibleInterFoam, compressibleInterDyMFoam and compressibleInterFilmFoam.
The prototype compressibleInterPhaseTransportFoam solver is no longer needed and
has been removed.
In this version of compressibleInterFoam separate stress models (laminar,
non-Newtonian, LES or RAS) are instantiated for each of the two phases allowing
for completely different modeling for the phases.
e.g. in the climbingRod tutorial case provided a Newtonian laminar model is
instantiated for the air and a Maxwell non-Newtonian model is instantiated for
the viscoelastic liquid. To stabilize the Maxwell model in regions where the
liquid phase-fraction is 0 the new symmTensorPhaseLimitStabilization fvOption is
applied.
Other phase stress modeling combinations are also possible, e.g. the air may be
turbulent but the liquid laminar and an RAS or LES model applied to the air
only. However, to stabilize this combination a suitable fvOption would need to
be applied to the turbulence properties where the air phase-fraction is 0.
Henry G. Weller, Chris Greenshields
CFD Direct Ltd.
- the expansions were previously required as slash to follow, but
now either are possible.
"<case>", "<case>/" both yield the same as "$FOAM_CASE" and
will not have a trailing slash in the result. The expansion of
"$FOAM_CASE/" will however have a trailing slash.
- adjust additional files using these expansions
Support the following expansions when they occur at the start of a
string:
Short-form Equivalent
========= ===========
<etc>/ ~OpenFOAM/ (as per foamEtcFile)
<case>/ $FOAM_CASE/
<constant>/ $FOAM_CASE/constant/
<system>/ $FOAM_CASE/system/
These can be used in fileName expansions to improve clarity and reduce
some typing
"<constant>/reactions" vs "$FOAM_CASE/constant/reactions"
Within decomposeParDict, it is now possible to specify a different
decomposition method, methods coefficients or number of subdomains
for each region individually.
The top-level numberOfSubdomains remains mandatory, since this
specifies the number of domains for the entire simulation.
The individual regions may use the same number or fewer domains.
Any optional method coefficients can be specified in a general
"coeffs" entry or a method-specific one, eg "metisCoeffs".
For multiLevel, only the method-specific "multiLevelCoeffs" dictionary
is used, and is also mandatory.
----
ENH: shortcut specification for multiLevel.
In addition to the longer dictionary form, it is also possible to
use a shorter notation for multiLevel decomposition when the same
decomposition method applies to each level.
Correcting thermoSingleLayer.C mask field alpha to avoid heat sources where there is no film.
Tunning fvSolution for alpha for twoPhasePachuka tutorial
- Arrhenius viscocity model for incompressible viscocity.
- energyTransport FO for incompressible single and multiple phase
flows and viscousDissipation fvOption source.
- Tutorial to show the use of energyTransport:
multiphase/multiphaseInterFoam/laminar/mixerVessel2D
- Tutorial to show viscousDissipation:
compressible/rhoPimpleFoam/RAS/TJunction
- although this has been supported for many years, the tutorials
continued to use "convertToMeters" entry, which is specific to blockMesh.
The "scale" is more consistent with other dictionaries.
ENH:
- ignore "scale 0;" (treat as no scaling) for blockMeshDict,
consistent with use elsewhere.
- allows configuration without an environment variable.
For compatibility still respect FOAM_SIGFPE and FOAM_SETNAN
env-variables
- The env-variables are now treated as true/false switch values.
Previously there was just a check for env exists or not, but this
can be fairly fragile for a user's environment.
