The calculations for mixture rho and U have been changed so that they
represent phase-averaged quantities over the moving phases only.
The mixture density is used as part of the pressure solution to
calculate buoyancy forces. The pressure within a stationary phase is
considered to be decoupled from the moving phases; i.e., it is
considered self-supporting. Therefore the stationary phase density
should not form a part of buoyancy calculations. This change to the
definition of mixture density ensures this.
Lookup of models associated with unordered phase pairs now searches for
both possible pair names; e.g. gasAndLiquid and liquidAndGas.
Patch contributed by Institute of Fluid Dynamics, Helmholtz-Zentrum
Dresden - Rossendorf (HZDR)
The nonRandomTwoLiquid and Roult interface composition models have been
instantiated (and updated so that they compile), and a fuller set of
multi-component liquids and multi-component and reacting gases have been
used.
The selection name of the saturated and nonRandomTwoLiquid models have
also been changed to remove the capitalisation from the first letter, as
is consistent with other sub-models that are not proper nouns.
This model transfers a dispersed droplet phase to a film phase at a rate
relative to its intersection with a third phase. The third phase is
termed the "surface". It can be enabled in constant/phaseProperties as
follows:
phaseTransfer
(
(droplets and film)
{
type deposition;
droplet droplets;
surface solid;
efficiency 0.1;
}
);
The efficiency is an empirical factor which represents a reduction in
collisions as a result of droplets flowing around the surface phase and
not coalescing on impact.
This work was supported by Georg Skillas and Zhen Li, at Evonik
An additional layer has been added into the phase system hierarchy which
facilitates the application of phase transfer modelling. These are
models which exchange mass between phases without the thermal coupling
that would be required to represent phase change. They can be thought of
as representation changes; e.g., between two phases representing
different droplet sizes of the same physical fluid.
To facilitate this, the heat transfer phase systems have been modified
and renamed and now both support mass transfer. The two sided version
is only required for derivations which support phase change.
The following changes to case settings have been made:
- The simplest instantiated phase systems have been renamed to
basicTwoPhaseSystem and basicMultiphaseSystem. The
heatAndMomentumTransfer*System entries in constant/phaseProperties files
will need updating accordingly.
- A phaseTransfer sub-model entry will be required in the
constant/phaseProperties file. This can be an empty list.
- The massTransfer switch in thermal phase change cases has been renamed
phaseTransfer, so as not to be confused with the mass transfer models
used by interface composition cases.
This work was supported by Georg Skillas and Zhen Li, at Evonik
Blended models are now registered and can be looked up in the same way
as regular interfacial models via the phaseSystem::lookupSubModel
method. For example, to access the blended drag model, the following
code could be used:
const BlendedInterfacialModel<dragModel>& drag =
fluid.lookupSubModel<BlendedInterfacialModel<dragModel>>
(
phasePair(gas, liquid)
);
Here, "fluid" is the phase system, and "gas" and "liquid" are the phase
models between which the blended drag model applies.
Also added tutorial case demonstrating usage. Note that the new drag
models are symmetric and should be used without any blending.
This work was supported by Georg Skillas and Zhen Li, at Evonik
Two new phase models have been added as selectable options for
reactingMultiphaseEulerFoam; pureStationaryPhaseModel and
pureStationaryIsothermalPhaseModel. These phases do not store a
velocity and their phase fractions remain constant throughout the
simulation. They are intended for use in modelling static particle beds
and other forms of porous media by means of the existing Euler-Euler
transfer models (drag, heat transfer, etc...).
Note that this functionality has not been extended to
reactingTwoPhaseEulerFoam, or the non-reacting *EulerFoam solvers.
Additional maintenance work has been carried out on the phase model
and phase system structure. The system can now loop over subsets of
phases with specific functionality (moving, multi-component, etc...) in
order to avoid testing for the existence of equations or variables in
the top level solver. The mass transfer handling and it's effect on
per-phase source terms has been refactored to reduce duplication. Const
and non-const access to phase properties has been formalised by renaming
non-const accessors with a "Ref" suffix, which is consistent with other
recent developments to classes including tmp and GeometricField, among
others. More sub-modelling details have been made private in order to
reduce the size of interfaces and improve abstraction.
This work was supported by Zhen Li, at Evonik
MULES and CMULES have been extended so that the limits can be supplied
as fields. These arguments are templated so that zeroField, oneField or
UniformField<scalar> can be used in place of a scalar value with no
additional overhead. The flux argument has been removed from the
unlimited CMULES correct functions in order to make this templating
possible.
An additional form of limit sum has also been added to MULES. This
limits the flux sum by ofsetting in proportion to the phase fraction,
rather than by reducing the magnitude of the fluxes with the same sign
as the imbalance. The new procedure makes it possible to limit the flux
sum in the presence of constraints without encountering a divide by
zero.
Partial elimination has been implemented for the multiphase Euler-Euler
solver. This does a linear solution of the drag system when calculating
flux and velocity corrections after the solution of the pressure
equation. This can improve the behaviour of the solution in the event
that the drag coupling is high. It is controlled by means of a
"partialElimination" switch within the PIMPLE control dictionary in
fvSolution.
A re-organisation has also been done in order to remove the exposure of
the sub-modelling from the top-level solver. Rather than looping the
drag, virtual mass, lift, etc..., models directly, the solver now calls
a set of phase-system methods which group the different force terms.
These new methods are documented in MomentumTransferPhaseSystem.H. Many
other accessors have been removed as a consequence of this grouping.
A bug was also fixed whereby the face-based algorithm was not
transferring the momentum associated with a given interfacial mass
transfer.
Multi-region PIMPLE controls have been applied to the chtMultiRegionFoam
solver, and a transonic option has been implemented.
The new PIMPLE controls let the solver operate SIMPLE mode. The
utilisation of library solution and convergence control functionality
has significantly reduced the amount of code in the solver. The
chtMultiRegionSimpleFoam solver has also been made obsolete, and has
therefore been removed.
A few changes will be necessary to convert an existing
chtMultiRegionSimpleFoam case to chtMultiRegionFoam. All the SIMPLE
sub-dictionaries in the system/<regions>/fvSolution will need to be
renamed PIMPLE. The system/fvSolution file will also need an empty
PIMPLE sub-dictionary. In addition, additional "<variable>Final" solver
and relaxation entries will be needed. For a steady case, adding a
wildcard ending, ".*", to the variable names should be sufficient.
Solution parameters appropriate for a steady case are shown below:
solvers
{
"p_rgh.*"
{
solver GAMG;
tolerance 1e-7;
relTol 0.01;
smoother DIC;
maxIter 10;
}
"(U|h|e|k|epsilon).*"
{
solver PBiCGStab;
preconditioner DILU;
tolerance 1e-7;
relTol 0.1;
}
}
PIMPLE
{
// ...
}
relaxationFactors
{
fields
{
"p_rgh.*" 0.7;
}
equations
{
"U.*" 0.5;
"(h|e).*" 0.3;
"(k|epsilon).*" 0.2;
}
}
This work was supported by Fabian Buelow, at Evonik
Tobias Holzmann provided cases for testing the convergence controls
The solution controls have been rewritten for use in multi-region
solvers, and PIMPLE fluid/solid solution controls have been implemented
within this framework.
PIMPLE also now has time-loop convergence control which can be used to
end the simulation once a certain initial residual is reached. This
allows a PIMPLE solver to run with equivalent convergence control to a
SIMPLE solver. Corrector loop convergence control is still available,
and can be used at the same time as the time-loop control.
The "residualControl" sub-dictionary of PIMPLE contains the residual
values required on the first solve of a time-step for the simulation to
end. This behaviour is the same as SIMPLE. The
"outerCorrectorResidualControl" sub-dictionary contains the tolerances
required for the corrector loop to exit. An example specification with
both types of control active is shown below.
PIMPLE
{
// ...
residualControl
{
p 1e-3;
U 1e-4;
"(k|epsilon|omega)" 1e-3;
}
outerCorrectorResidualControl
{
U
{
tolerance 1e-4;
relTol 0.1;
}
"(k|epsilon|omega)"
{
tolerance 1e-3;
relTol 0.1;
}
}
}
Note that existing PIMPLE "residualControl" entries will need to be
renamed "outerCorrectorResidualControl".
Application within a solver has also changed slightly. In order to have
convergence control for the time loop as a whole, the
solutionControl::loop(Time&) method (or the equivalent run method) must
be used; i.e.,
while (simple.loop(runTime))
{
Info<< "Time = " << runTime.timeName() << nl << endl;
// solve ...
}
or,
while (pimple.run(runTime))
{
// pre-time-increment operations ...
runTime ++;
Info<< "Time = " << runTime.timeName() << nl << endl;
// solve ...
}
OpenFOAM can now be compiled with single, double or long double scalars by
setting the WM_PRECISION_OPTION environment variable to either SP, DP or LP
respectively.
On most 64bit systems long double is stored as 128bit but computed in the
floating point hardware to 80bit. Due to the increased storage compared to
double precision cache and memory access is significantly more time consuming
causing a slow-down of floating point intensive operations by a factor of 2 to
3.
In early versions of OpenFOAM the scalar limits were simple macro replacements and the
names were capitalized to indicate this. The scalar limits are now static
constants which is a huge improvement on the use of macros and for consistency
the names have been changed to camel-case to indicate this and improve
readability of the code:
GREAT -> great
ROOTGREAT -> rootGreat
VGREAT -> vGreat
ROOTVGREAT -> rootVGreat
SMALL -> small
ROOTSMALL -> rootSmall
VSMALL -> vSmall
ROOTVSMALL -> rootVSmall
The original capitalized are still currently supported but their use is
deprecated.
Introduced thermalPhaseChangePopulationBalanceTwo- and MultiphaseSystem as
user-selectable phaseSystems which are the first to actually use multiple mass
transfer mechanisms enabled by
commit d3a237f560.
The functionality is demonstrated using the reactingTwoPhaseEulerFoam
wallBoilingPolydisperse tutorial.
Patch contributed by VTT Technical Research Centre of Finland Ltd and Institute
of Fluid Dynamics, Helmholtz-Zentrum Dresden - Rossendorf (HZDR).
This removes a class of flux-velocity decoupling ("staggering") relating to the
interaction between the virtual mass, lift and turbulent dispersion forces.
chtMultiRegionSimpleFoam needs to check whether or not the simulation is
at the end. To facilitate this, a Time::running method has been added.
The Time::run method was being used for this purpose, but this lead to
function objects being executed multiple times.
This resolves bug report https://bugs.openfoam.org/view.php?id=2804
Removed possibility for the user to specify a driftRate in the constantDrift
model which is independent of a fvOptions mass source. The driftRate must be
calculated from/be consistent with the mass source in order to yield a particle
number conserving result.
Made calculation of the over-all Sauter mean diameter of an entire population
balance conditional on more than one velocityGroup being present. This diameter
field is for post-processing purposes only and would be redundant in case of one
velocityGroup being used.
Solution control is extended to allow for solution of the population balance
equation at the last PIMPLE loop only, using an optional switch. This can be
beneficial in terms of simulation time as well as coupling between the
population balance based diameter calculation and the rest of the equation
system.
Patch contributed by Institute of Fluid Dynamics, Helmholtz-Zentrum Dresden - Rossendorf
(HZDR) and VTT Technical Research Centre of Finland Ltd.
allow renormalization of sizeGroup volume fractions for restarts involving
initial conditions with a slight degree of unboundedness
Patch contributed by Institute of Fluid Dynamics, Helmholtz-Zentrum Dresden - Rossendorf
(HZDR) and VTT Technical Research Centre of Finland Ltd.
