New functionality contributed by Mattijs Janssens:
- new edge projection: projectCurve for use with new geometry
'searchableCurve'
- new tutorial 'pipe'
- naming of vertices and blocks (see pipe tutorial). Including back
substitution for error messages.
Previously the inlet flow of phase 1 (the phase solved for) is corrected
to match the inlet specification for that phase. However, if the second
phase is also constrained at inlets the inlet flux must also be
corrected to match the inlet specification.
Loop over the edges of each block rather than the edgeList of the
topological mesh due to problems with calcEdges for blocks with repeated
point labels
- Write differences with respect to the specified dictionary
(or sub entry if -entry specified)
- Write the differences with respect to a template dictionary:
foamDictionary 0/U -diff $FOAM_ETC/templates/closedVolume/0/U
- Write the differences in boundaryField with respect to a
template dictionary:
foamDictionary 0/U -diff $FOAM_ETC/templates/closedVolume/0/U \
-entry boundaryField
Patch contributed by Mattijs Janssens
Patch contributed by Mattijs Janssens
- Added projected vertices
- Added projected edges
- Change of blockEdges API (operate on list lambdas)
- Change of blockFaces API (pass in blockDescriptor and blockFacei)
- Added sphere7ProjectedEdges tutorial to demonstrate vertex and edge projection
For example, to mesh a sphere with a single block the geometry is defined in the
blockMeshDict as a searchableSurface:
geometry
{
sphere
{
type searchableSphere;
centre (0 0 0);
radius 1;
}
}
The vertices, block topology and curved edges are defined in the usual
way, for example
v 0.5773502;
mv -0.5773502;
a 0.7071067;
ma -0.7071067;
vertices
(
($mv $mv $mv)
( $v $mv $mv)
( $v $v $mv)
($mv $v $mv)
($mv $mv $v)
( $v $mv $v)
( $v $v $v)
($mv $v $v)
);
blocks
(
hex (0 1 2 3 4 5 6 7) (10 10 10) simpleGrading (1 1 1)
);
edges
(
arc 0 1 (0 $ma $ma)
arc 2 3 (0 $a $ma)
arc 6 7 (0 $a $a)
arc 4 5 (0 $ma $a)
arc 0 3 ($ma 0 $ma)
arc 1 2 ($a 0 $ma)
arc 5 6 ($a 0 $a)
arc 4 7 ($ma 0 $a)
arc 0 4 ($ma $ma 0)
arc 1 5 ($a $ma 0)
arc 2 6 ($a $a 0)
arc 3 7 ($ma $a 0)
);
which will produce a mesh in which the block edges conform to the sphere
but the faces of the block lie somewhere between the original cube and
the spherical surface which is a consequence of the edge-based
transfinite interpolation.
Now the projection of the block faces to the geometry specified above
can also be specified:
faces
(
project (0 4 7 3) sphere
project (2 6 5 1) sphere
project (1 5 4 0) sphere
project (3 7 6 2) sphere
project (0 3 2 1) sphere
project (4 5 6 7) sphere
);
which produces a mesh that actually conforms to the sphere.
See OpenFOAM-dev/tutorials/mesh/blockMesh/sphere
This functionality is experimental and will undergo further development
and generalization in the future to support more complex surfaces,
feature edge specification and extraction etc. Please get involved if
you would like to see blockMesh become a more flexible block-structured
mesher.
Henry G. Weller, CFD Direct.
to handle the size of bubbles created by boiling. To be used in
conjunction with the alphatWallBoilingWallFunction boundary condition.
The IATE variant of the wallBoiling tutorial case is provided to
demonstrate the functionality:
tutorials/multiphase/reactingTwoPhaseEulerFoam/RAS/wallBoilingIATE
Contributed by Juho Peltola, VTT
Notable changes:
1. The same wall function is now used for both phases, but user must
specify phaseType ‘liquid’ or ‘vapor’
2. Runtime selectable submodels for:
- wall heat flux partitioning between the phases
- nucleation site density
- bubble departure frequency
- bubble departure diameter
3. An additional iteration loop for the wall boiling model in case
the initial guess for the wall temperature proves to be poor.
The wallBoiling tutorial has been updated to demonstrate this new functionality.
